Frigidaire 5303935066 Burner Igniter for Oven Burners, Gold

Easy to install, only had to change the mounting cover to my old one. Origional manufacturer part. Stove works as it should.

Had to replace the igniter in my oven. Bosch no longer makes the exact same original part, they only had a generic that would work and it was $60. After researching knew this one would fit. Easy install and working perfectly oven heats up quickly and is working great.

Oh how nice is it to get an OEM part at a reasonable price. Being an OEM part, it matched right up to the burner. Easy install, all parts provided and easy to read instructions. Oven fired right up after installation.

OEM part. Easy to install and got my oven working again - Dynasty model - DGRSC-30-4

So ever since we moved into our hose, the gas oven (Kenmore) was very, very slow to preheat, and sometimes we would catch wiffs of gas. Finally it started really smelling badly like gas. After doing some research I removed the bottom oven pans and watched as my ignitor bar glowed a weak orange and saw that it took more than 3 minutes to ignite the gas, which then was a very weak flame. I ordered this replacement part, as the "actual" part from sears is literally triple the price and still doesn't come with the connectors. As others have said, this replacement is as easy as follows: 1) Remove the various covers on the bottom of your oven (simply remove a few screws) 2) Remove the warming drawer (so you can get to the ignitor connectors) 3) Unplug all of the various connectors that come from the ignitor bar. It helps if you take a picture before hand so you know what connections go to what. 4) Unscrew the gas tube and remove the whole assembly (gas tube + ignitor bar + wires). This technically isn't required but I found that it made things easier. 5) Unscrew the ignitor bar from the gas tube (I had to actually hacksaw off one of the screws because the threads were completely stripped, but that doesn't have anything to do with this product) 6) Clip off both wires coming from the ignitor - clip them a couple of inches from the ignitor - having extra wire doesn't hurt. Make note of which wire went to which connection on the ignitor so you can match it up with the new one. 7) Strip ~3/8" off of the ends of the wires you just cut. 8) Use the provided ceramic wire nuts to twist the old wires/connectors to the new wires on the new ignitor. Note - this is why I gave this product only 4 stars. The ceramic NUT that I had was loose in with the bubble wrap and the other ceramic nut was no where in sight, so I ended up using electrical tape good to 220 degrees for that connection since ceramic wire nuts are not readily available at stores and I wanted to see if the ignitor bar was even the problem. 9) Screw the ignitor bar back on the gas tube 10) Feed all the wires and connectors back through the bottom of the oven and reconnect 11) Reinstall the gas tubes. Turn on the oven and watch to match sure it's all working properly. Mine did! My oven that used to take 30+ minutes to preheat now heats up to 400 degrees in less than 10, and now lights in approximately 30 seconds (instead of 3+ minutes, like before). 12) Reinstall the covers on the bottom of the oven, and you're done. Enjoy your new ignitor bar (and grumble about the fact that you received only one nut)

Worked perfectly in our Frigidaire Gallery gas oven. The OEM did have the shield like this one but it’s a perfect fit. This was a pretty easy repair for someone with average skills, just be sure to check for gas leaks due to pulling the stove out. Saved us a ton of money. OEM lasted 15 years, time will tell with this one.

My old oven element was red hot but took >6 minutes to turn on the gas. This new one worked well, gas on after 30sec (about the same as my broiler igniter). Old one measured 180 ohm, this new one was 100 ohm (both measured cold). Old one had extra heat shielding on the wires, which this new one lacked. Great cheap easy fix for my old frigidaire gas stove. Hope it lasts.

easy to install perfect fit and works great

Easy to install and will use this product again in the future.

My gas oven works again!!

Very inexpensive and easy to replace the old one.

Good price, fast ship, replaced my Wolf stove igniter with perfect fit (even though it's a tad shorter on the back) - see picture of part I replaced

Same day delivery on an oem part, fixed my oven couldn't be happier