10-In-1 Multi-Tip Folding Magnetic Pocket Screwdriver with Carrying Clip and Bottle Opener, Includes 3/16" and 1/4" Slotted, PH1, PH2, T15, T20, S1 and S2 Bits

Great driver with sturdy handle for twisting!

bought one of these and the magnets came loose one day, and then all of them eventually. emailed per diections on their website and got a brand new one and the magnets are all good months later.

It comes in handy more often than I thought. It fits right into your pocket and feels good in my hand. The only gripe I have with it is the extension neck is loose and tends to fall out. I fixed that by putting a rubber band around it when it’s folded. I tend to use it without the extension to avoid it from getting stuck in a tight screw. 4 out of 5 for the extension being loose.

seems like a good edc tool but could easily have been better. extention piece is the main issue. the body is square which can hang up in tight spots. the connection to the main tool is just a hex shaft into holding onto a weak magnet. will likely fall off if kept in the outside of a bag or belt. would have been considerably better if it could lock into an impact driver and have a detent retention to prevent falling out of the main body. opposite side that hold the bits is too tight, likely due to over paint, needed pliers to remove the bits from the tip. bits were not the ones that were advertised but I'll replace with higher quality bits so it was a non issue. Will either replace win round apex bit holder or glue it in place to just act as a cover so the bits don't fall out. overall a disappointment but i think i had too high of expectations. Will work for now.

I carry this along with my leatherman in my bag. It has handled every small job I have thrown at it. Quick repairs on ac's, light sockets, and such. Great tool, but I did switch out the extension for a Milwaukee. I also cemented it in place so it could fall out.

This is a great screwdriver. My only recommendation is to take off the square extension and put a round one on. The square one can be difficult in tight spots. The round one has been perfect on this. I work as maintenance in a machine shop. I use this on some tough screws. Even using the handle as leverage at a 90 degree angle, it holds up great and takes the extra pressure. Great design, wish it held more bits.

I keep this in my hunting bag to adjust my crossbow scope and make sure all the screws, etc. are tight. I love the fact that the tool allows you to open it at a 90 degree angle which allows you to get more torque and break loose stubborn screws, etc. The bit options included fits a wide variety of things that you will encounter with hunting equipment and most any type of gadgets in general out there.

The magnet is so weak, the bit holder practically flew off into the darkness (I was even trying to be careful with it after playing with it and reading the reviews). Great idea, but implemented poorly. If the bit holder had a detent and/or a stronger magnet, that would be a good improvement. As it is now, I'm out a bit holder and a bit. I think when I get a replacement, I'll epoxy it on. Since I only used one bit for a few minutes, I can't comment on the durability of the bits. My opinion for prospective buyers is that I would pass on this. If the holder won't survive a minor bump, it's not worth the trouble. Can't return it since part of the tool is missing. A follow-up after looking at it. I will reverse the carry clip. As received, the bit holder is down, which (unless I epoxy the replacement) would make it easy to drop off. I can't imagine it would survive more than a day or two at work without falling off unless I reverse the carry. I may try loc-tite before I go with the permanent epoxy solution.

純正の？四角いエクステンションバーが、イマイチでした。マグネットが弱く、狭いところで回しにくい。本体は結構重いためか丈夫です。ビット長は25mm、HEXビットは6mmまで内臓可能、1/4ソケットアダプタは太すぎて入りません。 今はビットをつけた時に、本体とツライチになるようエンジニアのDR-322を短く切って使用。これで見違えるほど使いやすくなりました。また、DR-322にビットをつけたままにしているので、ビットを計9種類持ち歩けます。プラスの1から3、マイナスの4と6mm、HEXの3〜6mmがこれ一つで済んでいます。 使用感ですが、とても良いです。 ポケット入れておいて、サッと出せる事が最高です。ツーリングの時にもポケットに入れてます。他の工具はバイクに収納しておけばOK。もちろんアダプタを付ければソケットも回せます。フレームは金属製で、意外と捻れずトルクもかけられます。また、赤い部分はプラスチック製なので、冬でも冷たくないです。ただ、高いですね。海外サイトで検索するとお手頃価格で買えそうなのに、残念。 ですが、私にとって公私共にかなり重宝しているので星5です。 国産で作って欲しい工具です。

The square bit holder may cause issues but just use an extension. Otherwise I love the design and weight to it.

Magnet weak

Great idea executed in the cheapest fashion possible the magnet started falling out within a couple months

As you can see from the video the magnet that holds the extension is prone to fall out. Other than that, feels solid, and it's pretty useful. They just need to improve the magnet.