Tungsten Carbide Steel Double Cut Rotary Burrs Set for Rotary Tool, 10pcs 1/8 inches Shank Fits Rotary Tool for Grinder Drill, DIY WoodWorking Carving, Metal Polishing, Engraving, Drilling

Tungsten Carbide Steel Double Cut Rotary Burrs Set. Amazing value if used properly and accurately with cutting wax they out performed far more expensive cutters.

I’ve used one of these to grind a few dodgy welds in stainless steel and it’s doing fine. I’m running it close to its max RPM in a hand held die grinder rotary tool and at that speed it throws off a steady shower of tiny chips and shapes the metal at a slow and steady pace good for control. No sign of the bit wearing yet. I’m used to the various bits for rotary tools wearing out after only a small amount of use so these have exceeded my expectations.

Make sure you check the size. Pretty decent carving through (small bits of) wood. Better for a dremel (or equivalent) than a drill - but still usable.

It did the job. I had two drills on the go. The little ball is a monster 😂

I bought this set to try to remove a set of locking nuts that had a broken key , Itade short work of the job , drilled between the locking nut and the security ring , once id drilled into it a sharp hit with the hammer and chisel the outer ring snapped, , than a couple of blows with the hammer and chisel the locking nut came off , the carbide bit cut in deep enough to give a good solid ridge to use chisel, I'm sure I'll findany more uses for the bits , wasn't honestly expecting it to cut in the way it did ,

Needed to remove the outer ring of a bearing that was fitted flush and had no access from behind. The bearing had collapsed and rusted solid. Took some time but the cylinder cutter fitted into an electric drill slowly ground its way through the outer ring of the bearing allowing it to be removed.

Terrible quality. Barely does anything. I don’t use this and I don’t know what I could use it for as it is just such poor quality. I bought the machine with it and no place to use it perhaps for arts and crafts really

Not bad, generic items but if you dont run them too fast and hot they work on , used on steel exhaust header and broken bolts to clean up for a weld and di the job, plus lasted longer than the dremel they were used with! some chipping fo the blades but i guess thats not unusual

Très bonne qualité et très performant même sur de l’inox. Préférez mettre au plus près du mandrin pour éviter de localiser.

Premier usage, c'est très efficace ! Utilisation en vitesse rapide conseillée, les dents sont féroces ;)

Köptes på chans för borttagning av avskjuvade och fastkorroderade rostfria skruvar i aluminium. Dessa bits ihop med Dremel fungerade tillfredsställande till detta. Inte den snabbaste avverkningen men helt OK. Ville inte borra med risk att göra problemet värre ifall borren går av.

Ich habe das Hartmetall-Frässtifte-Set mit meinem Dremel 3000 ausprobiert und bin bisher sehr zufrieden. Für Holzarbeiten sind die Fräser echt top – ich musste z. B. eine Wohnungstür anpassen, und das ging damit richtig gut und präzise. Metall habe ich noch nicht getestet, aber die Verarbeitung wirkt hochwertig, das Material robust und stabil. Auch die Verpackung macht einen guten Eindruck – alles sitzt sicher und ordentlich. Für alle DIY-Projekte, Gravuren, Schnitzarbeiten oder Feinarbeiten ist dieses Set wirklich praktisch. Ich freue mich schon darauf, es auch für Metall auszuprobieren, und denke, dass es dafür genauso zuverlässig sein wird. Für den Preis definitiv eine lohnenswerte Anschaffung!

Metal bir parça üzerinde kanal açmak için satın aldım. Matkap ucuna takarak kullandım. İşimi tam istediğim gibi gördü. Kullanım sonrası herhangi bir aşınma veya yıpranma oluşmadı. Kargo süresi makuldü. Tavsiye ederim.