Freud PB-007: 1" (Dia.) Forstner Bit

This thing cuts like a demon! I've drilled at least 5 deep holes so far and it hasn't lost any sharpness. No wandering, which was a big problem with my first set of Forstner bits. The scores around the mouth of the hole are from me having a little trouble holding the drill because of arthritis and I was hurting pretty bad. It measures dead on 1". Stays firmly in the chuck. Does exactly as they claim. Good quality, decent price. I hope the sharpness lasts! I've only had it 2 days.

If you want clean, accurate, well cut holes then these are the bits you should buy. I needed to cut a one inch drain hole in a stiff rubber water heater drain pain that was a half an inch thick. I cut through it with my Freud Forstner bit in less than a minute leaving a perfect one inch hole. Yes, you will pay more for these bits, but they are worth every penny you spend on them. Freud bits are sharp, durable and will cut through wood and rubber with near perfect precision. I highly recommend them.

This drill set delivers smooth, accurate cuts with minimal effort. The steep angled cutting edges and serrated design make a noticeable difference, especially when drilling flat-bottom, pocket, or overlapping holes. Even in dense hardwood, the bits stay sharp and cut cleanly without burning. The 7-piece range from 1/4" to 1" is versatile and well-suited for fine woodworking. Highly recommended for anyone looking for professional-quality results.

There’s no comparing these fine bits to the cheap Chinese knock-offs that have flooded the market. The Freud forstner bits are worth the investment. You could spend more, but honestly, I wouldn’t know why. I only wish the shanks were longer so I could bore deeper holes.

This is a precision tool! It is heavy and extremely sharp. It cut through hardwood easily.

When I need a through hole I usually don't care so much about the quality of a forstner bit and even the cheap ones usually will do ok, but when I need a good clean flat bottomed hole I still look to Freud first and I prefer these "older" style rather than the carbide bits. These are still really well ground and still made in Austria. I considered trying out the Bora forstners...photos look nice and they're Austrian as well...but stuck with tried and true. Put it to use immediately and nice clean entrance and good looking flat bottom in both baltic birch ply and solid canarywood. I wish Freud hadn't discontinued so many sizes in their forstner bits...would love to have a 30mm and know that I could still get smaller 16ths again. I don't know if it's true that the Diablo bits are the same, just a marketing shift, but the ones I've seen don't look as nicely made as the Freud label and for this size they aren't even ground in the same style. If it's for woodworking instead of utility/construction, stick with Freud or Fisch (or Fomag...$$).

This bit is amazing! Drilled 79 holes in 1.5 inch thick maple and it’s still perfectly sharp. Each hole was nice and clean on the start and of the 79 only about 10 had any tare out when bing used with a cordless drill and no backing on the other side of the hole. Made a custom peg board for my home climbing gym.

First, a little about me. I’m a weekend woodworker, mostly craft and art pieces and some home repairs. For 40 years I have sufficed with a power drill and regular bits, occasionally a spade bit for larger holes. Then I decided on a craft project where I wanted really smooth precise holes (hence the purchase of a drill press as well, don’t tell the wife). To make the holes I bought a cheap set of Forstner bits. You’ve seen them here on amazon, seven bits for $12. What could go wrong? Well, they worked way better than my old bits. Amazingly better. But I noticed they got dull within a few uses. So I treated myself to this Freud bit. Ohmyfreakingawd!!! This was so sharp it was like a hot knife thru warm butter, and that was drilling into sycamore. So smooth, so fast, it was amazing. No more generic bits ever again for me. I am now going to splurge on Freud every time. They are totally worth it. Do yourself the favor and try them.