Creality Original Magnetic Frosted Surface 3D Printer Heated Bed Cover 235X235mm for Ender 3/Ender 3 Pro/Ender 3 V2/Ender 5/Ender 5 Pro/Ender 5S 3D Printer

The Comgrow Original CR-10 V2 Ultra Flexible build plate works great! Prints stick firmly during use and release easily once cooled. It’s durable, easy to clean, and makes 3D printing much more convenient. A must-have upgrade for my CR-10!

After crashing my print head into the original build plate and scratching the heck out of it I couldn't find a new OEM bed at a reasonable price. This fit perfectly and held in place without issue. The texture is good and I haven't had a print break free of the bed. The magnets did not work for me because I placed this on top of the OEM glass bed and clipped it into place.

I tried getting my table leveled out with this magnetic surface, first using the paper method. However when I brought my Z-axis down in the center of my printing bed to level it evenly after I've "AUTO HOMED" it, it would keep maxing out the Z-Stop switch (that thin metal piece that makes contact and presses the tiny red button). Now I know some of you are thinking, "Well, why don't you raise your printing bed then?" ..I've also tried that. Unfortunately the adjusting screws are only adjusting the CORNERS of my bed, resulting in the middle of the bed being too low. (Picture a square, dining plate that you'd eat on but not that exaggerated) I can't seem to figure out how to raise the middle of my printing bed that way I can adjust the corners accordingly, to level with the middle. My corners are then grinding whilst the middle is too low. I think my heating plate may be too bent and sunken in the middle, or lifted around the edges causing these results. ALSO I am unfortunately unable to lower the physical Z-Stop attachment, It's in a fixed position with 2 screws so It cannot slide down. If anyone has a fix or a neat trick to get around this issue, please help me out, I'd REALLY like to use this magnetic surface. It is a really nice product. Thanks! (Creality ENDER-3 MAX) **EDIT/UPDATE** (5/4/23) -- Turns out my heating bed is indeed warped, either around the perimeter or the center. My Z-Stop issue had absolutely nothing to do with this magnetic plate. Since I don't wanna purchase a new heating bed and ANOTHER magnetic print surface and dealing with all that hassle, I'll just be going back to a glass bed. Great product though! Just a waste of my money because I wasn't aware my heating bed was warped until I applied my magnetic adhesive and ran my leveling steps hahah. Hope this information helps someone before purchasing! Make sure nothing is bent or warped! Cheers!

Quick shipping

Adhesion is pretty good, easy to install and use, but after about 15 prints it had a large piece just peel off. Not sure if this is common but I hope not. Update: got the 2nd one after returning the first one. My printer was down when it arrived so I had it a few days before I got to use it but here it is only a week after I got it and it already cracked and peeled after about 8 prints and I had problems with it the entire time. It stuck alright but too well. At a bed temp of 60 and PLA at 200 it actually even adhered the underside magnet to the magnet adhered to the bed but only directly under the print. I literally had to pry it off the bed before I could begin to remove the print from the surface. Now there's no option for return or refund or anything so I guess I'm just screwed out of my money. As the picture shows, you can see that it was leaving a layer of PLA (I tried 3 different colors just to be sure my filament was not the issue). I didn't use anything on it at all, no alcohol, or even water. This is probably only good if you are doing prints with a large contact area or a large raft and still peel it evenly while it's still hot. If you doing small parts or anything do not use it.

This plate is awesome IF you can get the filament to adhere and z-offset to be stable. I have a difficult time getting consistent prints from this build plate. I can print a part and it is awesome BUT if I try to print the exact same part again it just wont print without issues, that being filament not sticking to the plate and having to change the z-offset to get it to print. You may have better luck than me. Regular PEI plates print fine. BUT this plate is SOOOO cool when it prints. It is like the coating is not stable on this one side. Pics dont do justice to these prints Update: After messing with trying to get this plate to be consistent, I found that the POM wheels on the Y carriage were worn so would not hold bed in proper alignment. Installed new wheels and consistency improved dramatically. Changed rating to 4 stars brcause plate not totally to blame for poor consistency. Z-offset is critical to get the desired look. Overall very satisfied with plate SO FAR !! I am having to run higher bed and nozzle temps for adhesion. My camera just wont do the pics justice. Print looks better than pics illustrate. Finally got a decent pic, red

I have a Creality CR-10S Pro V2 and I wore out the print bed material after about 5 months of heavy printing. I am so impressed with this product! Easy to install (after pealing off the old worn-out surface from the aluminum print bed plate and removing the glue with MEK -- not fun!). Great bed adhesion. No glue or hairspray needed. Very easy to remove prints. No more scraping prints off the print surface. I don't think that I will have to replace this build surface for a long time! I highly recommend this product. Also, after applying the magnetic material to the aluminum print bed plate, I used Kapton Tape to secure the build plate to the aluminum heat plate. No clips! The Creality build surface is then installed and removed.

Il piano è molto flessibile e soprattutto molto aderente. Si, come hanno scritto in molti si fa fatica a staccare i pezzi, con alcuni materiali è meglio farlo a caldo, con altri meglio aspettare che si raffreddi. Se tentate di stampare superfici ampie con ridotto spessore (es. test del piano di stampa) con il piano nuovo, dovrete raschiarle con la spatola metallica per rimuoverle. Fortunatamente con l'uso la capacità di adesione tende a diminuire e quindi a stabilizzarsi. Il piano acquistato ha una superficie di 310x320, indicato per una CR10S pro, ma secondo me per questa stampante sarebbe stato meglio un 310x310 che permette di utilizzare anche il piano di alluminio di supporto, ed avere lo spazio per bloccarlo con delle mollette. Ho provato fino a 80° di riscaldamento senza nessuna conseguenza per gli adesivi magnetici (nessuna bolla o distacco). Penso che tutto sommato sia valido e lo ricomprerei.

Avec le plateau d'origine, j'ai toujours beaucoup de difficulté pour réussir mes prints : surface non planes de l'accroche, mauvaise adhérence mal grès le recours au scotch de masquage et de la colle en bombe... Maintenant le lance mes impressions les yeux fermés directement sans jupes, ni radeaux et le décollage des pièces même fines est un véritable plaisir, je n'utilise plus mes spatules ou lames pour décoller les pièces, même avec le lit chaud, je plie un peu le plateau, récupère la pièce et il se remet en place nickel sur la base magnétique que j'ai collé sur la plaque d'

Este es un producto de esos que no trasmiten mucha confianza y no lo digo por el material que me parece correcto, pero cuando lo usas cambias de manera de pensar ya que cuando lo utilizas ves que funciona, espero siga asi mucho tiempo.

Made a Cyberhedron Lamp. Didn't need a glue or anything, stuck to mat perfectly. Using PLA at 200, and mat at 60.

La compré por que Creality es calidad, pero para imprimir en PETG no vale, en la descripción no pone nada de materiales que no se puedan imprimir. Quedan los resto de la impresión que no he sido capaz de eliminar, a parte de que cuesta muchísimo despegarlo. Podrían poner para que materiales es apta esta cama flexible y para cuales no !!! La verdad es que ha sido una auténtica desilusión.