Bounty Hunter TK4 Tracker IV Metal Detector – All-Terrain Gold, Silver, Coin & Relic Finder with 8" Waterproof Coil, 3 Detection Modes – for Adults & Kids – Made in USA

As a low cost metal detector I give this thing five stars. I bought this Detector several months back and enjoy it's relative ease of use, and it DOES find what you are searching for (coins, rings, earings, necklaces, etc). The other reviews here pretty much wrap it up as a good (affordable!) unit, but I wanted to make a few comments from an amateur's point of view: - This detector has, of course, the discrimination circuitry used to tell the difference between the various metals helping you to avoid digging up junk like soda can pull tabs which are everywhere. It does work pretty good, BUT - I have found that by using the Tracker IV discriminator, you will most likely be missing some good stuff. I have gone back over "Discriminated" areas again in "All Metal" mode and found some nice stuff that Discriminate didn't catch. Granted I am no pro, but the fact is if you want to get every coin, every ring, or every cool item of various metals, you may want to consider just using "All Metal" mode. I almost exclusively use it now and although I sift through some absolute junk. I have found a bunch of coins, necklaces, pendants, etc that I would have otherwise missed. Use the Discriminate mode when looking for that gold wedding ring your wife through at you in the back yard... - Invest in the 4 inch "Gold Nugget Coil" which is far superior at pinpointing metal. The stock coil works fine but is a tad ambiguous as to precisely where your coin, ring, (or pull tab) is. The smaller coil reduces search time and I am glad I have one. - I bought the recommended Bounty Hunter Headphones (to save battery power), but have found them to be a bit more trouble than help. When I detect something I squat or sit down and dig. I set the detector down so the coil is near the dig zone so I can waive clumps of dirt (or sand) in front of the coil as I search. The problem is the headphone's wire tends to be always in the way when I perform this move. I get tired of "untangling" so I don't use them anymore. Maybe I'm just getting old. - The meter is of no value for anyone who can hear the audible report. It has no "range" to judge metals you are passing over. It simply swings hard to the right no matter what from what I can tell. I have tried different modes and different metals to test it, but it seems to merely swing hard to the right as you pass over any type of metal / alloy. I can see how this would still be useful to a deaf person, but it just as easily could have been a bright light bulb instead of a meter. I won't ding this low cost detector for that though because I'd still dig if it was half scale or pegged. - And lastly a warning. If you go into a park, or any area attended by kids, you will be spotted. Within a short amount of time you will be surrounded by kids "helping you" to dig up buried treasure. At that point you have to decide whether to be a meanie and bark at them, or write the rest of the hunt off and let them shred the area every time the detector beeps. I generally tell them how it's been a long day and "see ya" since they will invariably have their hands in there digging away no matter what you say...

I chose the Bounty Hunter Tracker IV for one main reason — it keeps things simple. The setup is straightforward, it was quick to learn right out of the box, and the tone mode with the toggle switch that lets you flip between All Metal and Tone discrimination is exactly what I needed as a beginner. That toggle feature makes a real difference in the field. I can scan in All Metal when I want to hear everything, then flip to Tone mode to get clearer signals and cut down on unnecessary digs. It’s user-friendly, reliable, and perfect for someone just getting started without a bunch of complicated menus. If you’re looking for a detector that’s easy to understand and has that helpful All Metal / Tone toggle, this is the one I went with and I’m glad I did. Highly recommended for beginners who want something simple and effective!

I have had little experience with metal detectors, except for having built one once about 40 years ago as a project I found in an electronics magazine. I still understand in principle how these devices work from that experience and from a general background in electronics. Basically a balanced circuit is produced in the two coils at the end of the unit. When the flux lines in the coils are changed by induced eddy currents (by passing near a metal object), a difference signal is generated from the unbalanced conditions which lets the operator know that something has changed in the field of the detector coil. BTW, this is why one must move the coil in order to induce a signal. A static coil does not experience any changes. Different metal groups produce different phase responses, which allow for some rough discrimination of the type of metal producing the response. My point is that these things can finicky as most anything that changes the reluctance of a tuned circuit will generate a difference signal. So the trick is to just generate a signal when an object of interest is passed over. All of that said, I am favorably impressed with the operation of this moderately priced unit. It is rugged. It is very stable. It is sensitive without being too sensitive so that too many false signals are generated. The notch filter function seems to work well. It does not seem to be much affected by soil mineralization (at least in my yard) or soil moisture levels. I purchased the unit to find nails in the yard. I had my roof replaced a couple of months ago and even though the crew did an excellent job and ran magnetic nail sweeps over and over the yard, I could still go out with a powerful hand held magnet mounted on a short wooden handle and find nails. After several weeks of this sporadic activity, I realized that if I were to have a shot at finding 99.9% of the extant nails, I would need a better way to detect them. Hence this detector. I use the detector in the non-discrimiating mode and have found nails that were obviously left over from when the house was built almost 20 years ago! For this purpose it has worked and worked well. I have even done a small amount of digging to get the long buried metal up and out of the yard for no other reason than I can locate it and then retrieve it. No treasure, so far. Learning to narrow down the source of a signal by making "X" sweeps takes a bit of practice. After only a few minutes, however, even a novice such as I can quickly get an idea of whether the object is on or under the surface and if it is iron/steel or not. The grand daughters, 6 going on 7, and 9 going on 14, have taken to this device in a big way. Let me explain. I salted two areas of my rather large yard with 1- $1 coin, 5 quarters, 5 dimes, five nickels, and five pennies each. These areas were well removed from one another. I made sure that the coins were not very visible, but otherwise were dropped randomly. When the grand daughters last came to visit, I asked them to help me find treasure in my yard. I produced two wadded up "treasure maps" and let them select which one they wanted. Then I showed them the metal detector and explained how it worked. I had a minute timer along with two baggies labeled with their names in my pocket. The timer was to keep the peace as each girl got ten minutes alternately. The baggies were to keep the loot separate and separated. I believe the 6.5 year old would still be out there looking, if we had not forced her to come in that evening. All in all the youngest found all but 6¢ but oddly enough, she ended up with 4¢ more than I had planted. You see, she found a dime that I had not put there! The older one came up 11¢ short and was most disappointed that her sister had found more than she! As a bonus, they did find 7 nails that I had not expected to find as these were in areas well removed from the perimeter of the house. I also had an opportunity to explain to the older one that this was an application of science, where she could use a device to sense things that she could not see, hear, or feel. This made an impression on her, I could tell. They want to come back and do this again! Suits me fine. So what does this have to do with a review of a purchase? This unit has worked well in not only my hands but in the little, inexperienced, and often clumsy hands of two children (after shortening the pole). It is light enough in weight that neither I nor the children had any difficulty using it. The smaller did have to use two hands, however. I am pleased with it in general, but I have yet to test it for unsalted "coin shooting" (I love that term), relic hunting, prospecting, or general treasure hunting as in finding objects of value say at a public beach, park, etc. I would recommend it as a good, affordable, general purpose metal detector, with the caveat that I have few benchmarks such as how a higher end unit would perform for comparison, such as a unit that worked by pulse induction, for example.

This is my first metal detector (though I've used other people's before), so, to figure out what to buy, I read many product reviews on amazon and on metal detector websites. I main hope to find old coins. I came to the conclusion that I should buy this detector along with the Garrett Pro-Pointer . Considering this product's relatively low price, I thought it might have trouble finding anything, but this detector is very good at finding coins as well as trash. (Note that I use this detector in conjunction with the aforementioned Garrett Pro-Pointer, which speeds up the recovery speed perhaps 10x and is amazing to see/hear in action. You really need both, or the recovery process will be excruciatingly slow.) After a few days' practice, I am starting to be able to discern the size and depth of an object even before digging, which helps me decide whether to even bother digging. (I realize I may be passing up some treasure, but digging up lots of trash is so discouraging!). So, now I am pulling up mostly coins and trash that's the same size as a coin. I still haven't found anything the least bit rare, and I figure my hourly "wages" have averaged about 40 cents (from the coins I find), but it's fun, and I'm still hopeful I'll find something worth talking about some day. In practice, I generally leave the sensitivity setting all the way up, the mode set to TONE (which beeps nicely to indicate treasure and beeps harshly to indicate trash), and the discrimination level set to about half way. However, if I am in an area that has hardly any metal and am struggling to find anything, I set the mode to ALL, and turn the discriminator down all the way (because that maximizes the machine's overall sensitivity). Once I get a beep, I switch to TONE and 50% discrimination to get an idea of what's buried. Later, I try to remember to switch the settings back to maximize sensitivity. There are lots of ways to successfully use the controls. The worst thing to do is to not bother learning how they work because they are essential to your success. The length of the stem of the detector is adjustable (just like on exercise equipment), so I shorten it to the shortest setting to fit it in my car's tiny trunk, and I lengthen it to the longest setting when I'm using the detector. To preserve battery life, I turn the detector off when It's located something. Then, I use the Garrett Pro-Pointer to narrow it down even closer, digging as needed. I turn the Pro-Pointer off ASAP to preserve its battery too. On the other hand, If I'm in an area that's chock full of coins, I don't bother turning either device off because doing so would slow me down too much and not save much battery life. Speaking of batteries: both devices take standard 9-volt batteries. I haven't had to replace the batteries during perhaps 20 hours of use! Aspects that surprised me: * It beeps if it bumps into something hard, such as a rock. At first, I thought it had found metal, but re-sweeping the area indicated no metal. * It is more sensitive when sweeping left and right than forward and backward. * It doesn't discriminate (between trash and non-trash) as well when sweeping fast as when sweeping slow. * Normally, it has to be moving to detect anything, but if the signal is very strong (such as when the treasure is on the surface or is large), it can basically be motionless and still beep. I haven't used it with a headset yet, so I can't comment on that aspect, but the built-in speaker is plenty loud for most of the places I've taken it. They say the battery lasts longer if you use a headset. I was debating whether to give this product 4 stars or 5. I decided to give it 5 stars because, for the price, I can conceive of no way at the present that anyone could improve upon it. Still, wouldn't it be cool to have a device that could definitively tell you what's buried down there?

So, basically, the only reason I purchased this was to find my mom's gold pendant in our backyard. We were cutting down a tree and building a fence, and at some point, her necklace had apparently snapped and fallen off. She told me there was no way we'd be able to find it in our large backyard, so naturally, being her child and all, I was immediately consumed by the need to prove her wrong. For starters, the price is fantastic compared to other metal detectors on Amazon. This made me a bit nervous, but the reviews were positive enough to convince me. The quality is remarkable and exceeded my expectations. Its lightweight, sturdy, and the grip was perfect for my blistered post-yardwork hands. Batteries weren't included, but it just needs two 9v batteries. It was easy to assemble (attaching two parts and putting batteries in). Additionally, it was extremely simple to figure out and use—this is crucial for my dad and I, as we frequently toss instruction manuals aside without reading them. It took us about 3 minutes to understand and adjust the sensitivity controls, and only an additional 5 minutes to figure out the "metal" we were detecting was actually the shovel we kept placing right next to it. If two ADHD adults who share one braincell can operate it, then basically anyone can. We found 13 screws, 11 nails, multiple sprinklers, random bits of metal scraps, a friendly slug (not metal but it was cool), my dad's keys (they fell out of his pocket into the grass, lucky for him we had a metal detector), and a bunch of other miscellaneous things. And, of course, I found my mom's gold pendant. Unfortunately, I probably could've done this without the metal detector, as it was actually just sitting on the cement a hundred feet away from the area we thought she lost it in. However, due to its size and my whole family's lack of vision, none of us would've seen it. I actually had to kneel down and squint to figure out what the metal detector was beeping at. Regardless, the praise I received inflated my ego, and now I'm at risk of the Gods striking me down for my hubris. In conclusion—I proved my mother wrong, returned her beloved pendant, had fun with my dad and sister, made my whole family think I was an expert treasure hunter, and now I have a super rad device that I kinda wanna take out to the desert next weekend. Tons of fun, 10/10. Highly recommend.

I have been doing this for 35 years and this is my 4th detector. My last one was a top of the line and had to part with it to raise money when I was out of work. I decided it was time to once again buy one and the price seemed right. Of course I cannot compare it to a $300 detector ( at the time ), you do really get what you pay for. Here is my take so far. The bad : No volumn control, one level fits all sound. Also, it was hard as heck to pinpoint the target. With my last detector, when I dug the hole, you simply placed the coil over the hole and found the object. With this unit, it only works when moving so you have to wave it back and forth while digging to locate the target. The good: It is super light weight, made almost 100% from plastic. You won't get tired as fast. Takes 2 9v batteries.( Batteries while wearing headphones last about 15-20 hours ) Probably ok for a beginner, however if you are an avid hunter and you can afford, spend at least $200.Once I find enough to pay this one off, I am going back to a better model. This model will NOT go deeper than about 6" on a quarter and to find older silver coins, this model won't work. I have challenged Bounty Hunter manufacturing to prove me wrong but they actually agreed with my test. They said they sell a more expensive model if you want more depth. UPDATE 2: OK have used for 1 month now and have found a total of $200.00 in gold jewelry. I know that because a reputable dealer paid me that amount for what I have found so far. I have now paid off the detector in just a months time. I am more impressed now, however, if you are wanting to find old deep silver coins you have two choices, buy a better machine, or use this one on all metal mode, go real slow and dig about 1000 lbs of trash for every coin found then still no guarantee.Also, with my old detector, you just held the detector over your hole and it beeped if item was still there. This detector is a motion detector so you have to swing it for it to work so pinpointing is litteraly a pain. By the end of the first day my shoulders were sore. * If you want a decent detector to just find recently lost coins around playground equipment, this detector is awesome with its three mode detection. If you want to do some serious silver hunting or looking for old deep buried coins,forget it. It is however great at finding old soda cans up to 12" deep. Maybe you can dig them all day and cash in the aluminum, you should be able to pay off the detector in maybe 75 years. Overall, like I said, Bounty hunter is one of the 5 oldest detector companies around but most of their equipment is geared towards beginners. UPDATE: 2013. Even though I kept the Bounty Hunter for a back up detector, Once I got back on my feet and was hooked again in metal detector, I did some research and ended up going mad and paying $1,800.00 for a metal detector. I have found more with the new one in 16 months than all 4 other detectors over 35 years. I am still glad I bought the Bounty Hunter and keep it as a back up cause it is so darn easy to use. Plus it triple paid for itself in less then 5 months.

We bought this because my husband lost his wedding ring in the yard in some tall grass. We looked for it for 4 nights in a row, but ordered this after not finding it the first night. It came in the fifth day and we found the ring in 5 minutes. Extremely easy to use, my nieces (5 & 10) enjoyed getting to use it. They have each asked for their own as gifts. It was easy to plop in the car and drive over to where we lost it, it took up no space, and was super easy to setup.

This is a nice unit. So far I have just used it in the yard to find my property markers.

Working fine

Helt ok 👍

Excellent product 👍

bon détecteur pour le prix rien a redire seule petit bémole aucune notice en français méme en cherchant sur le net quel galére . je recommande ce produit

Okay so i have done a bit metal detecting years ago and spent about £350 on a fisher detector which was very good. As i wanted to get back into this hobby i originally started looking on e-bay but soon realised that the prices were just silly for older detectors and also secondhand newer detectors such as the garrets 150 and 250. People are paying £30 - £40 less for a secondhand garret than they would pay for a brand new one with a guarantee? That just does not make sense to me. I did a bit research on the bounty hunter range and there are mixed reviews from both amateurs and so called 'pros'. Build quality has been questioned and it has been likened to a toy. Well, yes it is plastic in construction and i was a bit apprehensive about this, but in actual fact i now consider that to be a bonus. I have been out 3 times since 7th feb and its lightness is a real bonus, you hardly need any effort to use this detector. I first tried it the day after i received it, and it was so simple and enjoyable, i couldnt believe it. After an hour of searching i had found £1.44 and a brass tap. Not enough to retire on but great fun. The next time i tried it i went a bit further than the playing field and into the woods, and i had read the manual so i was able to use the discrimination modes. I found 8 coins, a mixture of half pennies, 2 x 20p pieces 2 x £1 coins an old penny and what looks like a coin with queen victorias head on it ( though this is pretty well worn) oh and an old dinky toy tractor which is in excellent condition. The third trip out was purely to test depth on various metals and to learn the different tones that it makes in the three different modes offered. I have no magical method to offer as these tests are very basic but i am learning to trust the detector and the tones it emits in certain modes. Its not a magic wand and its not 100% accurate. Whether thats down to me or what i dont know, but i feel fairly confident that i am learning and that the detector seems reliable. I shall hopefully be going to the beach fairly soon to test its capabilities and pitch it against my 2 mates, as yet unused , garret detectors. And thats the thing, its no good paying big money for a detector if youre not going to go out and use it regularly. These two mates of mine have had theirs since christmas but havent even used them in the garden yet !!!!! I would say this is a very good introduction to the hobby and that if you are prepared to read your manual and learn how to use the 2 controls and flick switch, then this will be an excellent choice for most people. People with expensive detectors will always 'knock' cheaper detectors, they have to justify spending their money dont they? UPDATE###### Just a quick update, my tally of coins now totals approx. 70-80. Ive been out about 7 times. The coins are king george pennies and halfpennies, queen victoria farthings,threepenny pieces, two shilling coins,queen elizabeth pennies (pre decimalisation) and loads of modern pennies,10p pieces,20p pieces, 50p and pound coins. Im mainly using 'disc' mode as i have been in high trash areas. Last week i found a queen victoria commemorative medal which i think is my best find to date. I am more than happy with the detector, the only thing i have slight doubts about is the depth at which it is detecting. All my finds have been fairly shallow, about 4 inches, so when i find less trashy areas im going to use 'all metal mode' as this apparently gives more depth !