Acrylic Panel and Case Joystick DIY Set Kits Replacement for Arcade Game Machine Cabinet Controller DIY Kit

Its made better then expected and really like this case the suction cups work extremely well my only negative thing is it collects fingerprints way to easily but easily solved with a graphics decal definitely planning on getting another one. Great buy

It's cheap, and it's solidly built. Can't really complain. The three top holes are not 30 mm but rather 24 mm. If you don't have 24 mm buttons, you'll have to make some modifications. I used a 1 1/8th Forstner bit and increased the hole sizes to accommodate 30 mm buttons. Additionally, the text and outline around the Start button hole flake right off. So, if that matters to you, be warned it's not going to remain.

I had built a cabinet and it became hard to move and work with... These replaced that and I just need to connect the two controllers to the RetroPie I was using before... it is not the same but it was a great approach to keeping everything neat without sacrificing the arcade experience.

This takes me back at the arcade. It's easy to assemble and it works on my retropie and raspberry pi. I use it a lot

I buy 2 of them and the sice of the holes is wrong, it says 2 holes from credit coin, the small bottons ones, and it don`t have those holes, I have to make them with a drill and even use a knife to adecuate the hole, and all that damage the stability of the box. It comes with 9 screws and 7 nuts (they dont even know how to count as it seems), so I get a lot of problems geting the small nuts in a hardware store, because it is really hard to find that size, so I have to replace all the 8 and it was really hard to find matching ones.

For the price I wasn't expecting much, and honestly, it still feels a bit overpriced if anything. Had to drill out the screw holes in the bottom housing. The quality of the acrylic cutting leaves a lot to be desired. There was a scratch on the top surface of mine despite the protective film. It's very shallow which means my wiring harness is crammed up against the bottom and puts a lot of pressure on the button connectors. Still, it suits my purposes well enough. To clarify, all of the button holes are 30mm despite how it looks in the picture. You'll need the screw-in type, as the acrylic is too thick for snap-in ones.

Back a few years ago, these off-brand plastic housings were adequate, and more importantly, they came with the requisite hardware to assemble properly. The quality has taken a HUGE hit and quite frankly, this is garbage. It doesn't come with proper screws to mount the top to the base. For some reason they do not fit through the base holes. The holes seem smaller in the plastic base than the top and the screws are not self-tapping, so the diameter is important. Something to keep in mind when ordering these types of cases. If I had more skill i suppose I could make my own, but these do save time, provided you get the right hardware. :)

Durable and the price is right. Plenty of room inside for customization.

Awsome

Good build quality, very nice product

天板が分厚い(5mm)。そのため押しボタンスイッチは ねじ式 でないと固定できない模様。 また厚さの分、ジョイスティックの軸も短くなる。 単純にケースとしては軽くて丈夫でコンパクト。ただ底面の吸盤の取り外しが非常に面倒くさい。

Veramente un buon prodotto. Leggero,robusto e a un prezzo più che equo. Una soluzione semplice,pratica ed economica per chiunque voglia dilettarsi nella fabbricazione di un arcade stick. Consigliato.

999円と格安だったのでポチッてみた。 天板のアクリル板が5mmもあるのでネジ止め式のボタンでないと厳しい模様。 上側3個が24mmボタン用で、他の8個は30mmボタン用の穴が開いており特に問題なくボタンの取り付け(もちろんネジ止め式ボタン)は可能でしたが若干ボタンの間隔が近いのかネジ止め用のリングを締める時に調整しないと干渉する場合があります。 なお自分が入手した商品はボディの下側のネジ止め用の穴が小さかったので4.5mmのドリルで穴を広げてからネジ止めしました。ここもあまり余裕がないのか通常のナットより大きいサイズのナット(フランジナットとか)は使えないようでまたネジの長さが長すぎるようでした。 なお天板にレバー固定用の皿穴とボディの下側を取り付ける為の皿穴が開いていますが、添付のサラネジ以外を使うと頭の大きさが違うらしくわざわざ頭が小さいサラネジとそれ用のサラモミをしているようです。 もしネジを交換する場合は気をつけた方が良いかと。 格安でアケコンのガワが手に入ると考えればコスパは良いが、やはり値段なりの商品か。 一応ですがセイミツ工業さんのLS-32でも取り付け出来たのでボディの深さも許容範囲かと思われます。