Honeywell Uvex Bionic Face Shield with Clear Polycarbonate Visor and Anti-Fog/Hard Coat (S8510)

I tried many face shields before this model and I've finally found the winner. It's extremely balanced and comfortable but has successfully protected my face numerous times from dangerous chunks of wood and bark flying off my lathe. The visor is micro-adjustable so you can fit glasses or a respirator underneath - comfortably! Very sturdy build but this shield is light enough that you forget you're wearing it. Tips: • Remove the protective film off the visor before using! • Push the head strap adjustment knob in to adjust. • Spend a few minutes customizing the fit - helps with comfort and you only have to do it once. With 2,784 possible adjustment positions, I'm sure you can find the perfect fit. Pros: • Outstanding optics. Clear field of vision ahead, lower and peripherally • Strong polycarbonate visor is Ansi rated • Replaceable visor and sweatband • Can be adjusted while wearing • Anti-Fog actually works! (model S8510 only) • Visor flips up and stays up until you tug it down Cons: • So comfortable that you'll forget you're wearing the shield • The Darth Vader look frightens my dog

Very comfortable fit, changing shields is quite easy, the shield does not fog up at all during the past two weeks that I have used it, there is no part of the shield that blocks your peripheral vision on the sides or front of your face. Wouldn’t hesitate recommending this to anyone looking for a good shield.

Was a little concerned when I took it out of the box because it felt lite and flimsy, but after I mounted the head harness on it, pealed the plastic off the inside and outside of the face shield itself, then tried it on, I was impressed! It's lite weight so you could have it on for hours and not get tired of wearing it. Plenty of room to breath and not fog up, and not feel like your wearing a diving mask. Good clear view of everything with no distortion. I'm a little concerned that the face shield itself will scratch easy and only time will tell. That said, it'll be good to keep liquids from splashing on your face from your chin to literally the top of your head. Also be good to prevent lite debris from hit your face or getting in your eyes and nose etc if your blasting with air. I'm not sure it will stand up to hot debris sparks from a grinder and the like because the shield will probably get burn specs/pocks/spots in it. If your working on a rusty car from underneath this would be better than safety glasses to keep dirt, rust and stuff out of your eyes. I've spent $20 on things of lesser value. If your power washing things this would be perfect. I'm sure you get the idea. Plenty of uses and Highly Recommended.

I have only just put it together, and have not actually worn it in battle yet! However, the first impressions are that it is light and very comfortable indeed. It almost seems too light, as to be effective should it get a large strike, eg exploding grinding disk. However, I have to trust that it has been rated correctly, so without a destructive test, I have no option than to believe it would offer said protection. The adjustments are good, and wearing glasses/goggles are no problem. I do however, question that the manufacturer states quite clearly that this is a secondary protection device, and that safety glasses/goggles must also be worn underneath (which many it seems do not judging by the various reports). I would have thought that the shield should be able to be worn as an alternative to goggles, as a means to protect not JUST the eyes, but also the face. Why should goggles also be worn, if indeed the shield is capable of doing its job? But, better safe than sorry huh, thats why we are 'here' looking at buying such items! I also purchased a replacement visor, so that if the supplied one needs replacing for any reason, I would be left without one while I wait for delivery. I suggest that you always keep a spare in stock. The only other concern I really have is, the cracking of the polycarbonate visor itself. This is a worry. If stress/ageing fracturing occurs naturally after a short time, as some reports say, then what does this mean to the integrity of the visor if it is struck by something hard, and if it is "aged"? I would like to see some testing done, and any concerns allayed by the manufacturer. As a matter of interest, I bought some safety glasses from China (NOT on Amazon), which ended up in the bin. They looked great, but when I tried bending the lens in my hands, they shattered into shards of plastic, like little daggers. Horrifying! Anyway, bottom line, the Bionic Face Shield fits very nicely, doesn't appear to fog easily, light and not cumbersome. The price seems somewhat high, especially the replacement visors which are ridiculously expensive really, but then, if they save your face (if), whats that worth to you? Hope this helps.

I'm a retired machinist with over 25 years running all sorts of machines. Because of this I've used all sorts of different face protection. I'm now getting into wood turning and even though I knew I needed a face shield I had been putting it off. I had neck surgery about 5 yrs. ago so my neck isn't as strong as it used to be so I've been putting off getting a face shield. Until I had a 3" inch long piece of wood come out of a piece of Willow I was turning and stuck in my hair. It just missed sticking me in the face and happened so fast I didn't even see it. That's when I decided it was time to get that face shield. After a lot of looking I picked this one. The clear part wraps around the front to the sides far enough to give a good wide angle view. The bottom of it dips down far enough to cover the throat area and the top curves up and back giving protection from flying pieces from the front. The head gear for holding it is far better than the usual face shields have. The Head Band has a dial at the back that you push in and turn to tighten or loosen it. It also has padding in the front and back. I might add more to the front in the summer for a sweat band but for now its OK. The band going over the top has the usual hole and pin adjustment. The hinges on the side can be adjusted to set the face shield closer or further away from your face and that's really nice. Its something that I haven't seen on any of the other face shields I've used. When it came it had protective plastic film on both sides of the clear face shield that I had to peel off. It's a bit difficult to get the shield into the shell so to keep from getting finger prints on the face shield, and possibly scratching it, I only peeled the plastic film cover back about half an inch to a inch from the edges. Then mounted it in the shell before I finished peeling the protective film off the face shield. This Face Shield is pretty light compared to a lot of the others but it's still heavy enough to notice. Since I've had my neck operated on I can only stand to wear this for a few minutes at a time. I'm hoping that as I continue to use it my neck will get stronger and it wont be so hard to keep it on. The only thing that would make it even better would be having some pieces of protective film to put on the face shield to help keep it from getting scratched. Then when they get too dirty to see through just peel them off and put on a new one. I've seen these for the Trend Airshield Pro. I might try some of those for this face shield. Overall I think this is about the best face shield/face protection you can get without going to a full helmet setup. I have no problem with giving this a recommendation for anybody that's looking for face protection while running a lathe, a line trimmer outside, a bench grinder/cutoff saw, or any of the other things that you could need good protection for your face.

What an upgrade! I've used the old style shields and they did their job, but were clunky, distorted vision, and annoying. This is light years ahead. The shield is optically excellent. There is no distortion across the field of view. The field of view is very wide and long (side to side and up and down). The supporting frame isn't in the way, even when the shield is pushed forward in the two mounting positions. I tried the shield forward because I didn't want it to fog the way my old one sometimes did. That wasn't needed. The anti-fog works well, at least when it's new. I don't know how well it will last, but it's great so far. This was going back and forth between a shop with a/c and a covered outdoor area (20 or so degree difference in temps) in about 70% humidity. Super cold may perform differently. The mask is comfortable on the head, with several adjustments to make it fit a range of wearers. Padding is good, and it stays in the up position until you pull it down. It's not difficult, either, and doesn't try to push the straps off your head if you adjust the shield position. Protection is good with good coverage from forehead to neck. I used it for metal grinding with handheld angle grinders and bench grinders, and a cold saw. There were times you could hear bits flick and hit the plastic, but it wasn't nicked up or damaged. Over time I'm sure it will succumb and need to be changed, but that seems like it will be a while out at this pace.

Excellent product. Crystal clear, does not fog when using a face mask under shield. Dust and particles from grinding wiped off easily and did not scratch. The headset is comfortable and the shield flips up easily. I was pleasantly surprised with the quality and would definitely buy again.

Ok, so let’s pretend that you don’t look like a space shuttle reject.... lol... That’s ok, smile, your alive,... right? I live my Covid Helmut ! I felt super self conscious the first time I wore it, but I also felt very safe, and feeling safe trumps embarrassment any day....So does breathing! I like this shied because unlike the other options for face shields this one you can clean the crap out of it over and over and it still looks and functions perfectly. it’s so comfortable to wear too.. you can wear a ball cap backwards or a hood with it too...and it covers your entire face. I can honestly tell you that in the last week I have had at least 4 compliments on it. Stuff like “ wow, that’s really great”, “ you must feel really safe with that on” and “did you get that on Amazon, is it heavy to wear?” If your on the fence like I was because you feel like people will be starring at you, well, they will be...but they will be wishing they had the courage that you do to wear it and protect themselves from a disease that could seriously kill you and your family. So what’s more important? If there’ are any morons out there who laugh at you.... so what, let them! Let them laugh all the way to the ICU and hop on a ventilator. Then they will be wishing they spent the. $20/ $30 and spared their life. Even if you don’t get a serious case of Covid, it can damage your lungs permanently. Why would you not do everything you can to prevent getting sick? Stay well !