24x36" PET Sheet

These worked perfectly for costume helmet visors. I 3D printed a couple of mandalorian helmets and wanted an easy way to swap visors of differing darkness, depending on the situation. These PETG sheets were perfectly clear and easy to cut with kitchen sheers. I added automotive window tint and installed with Velcro. I’m very happy with the price and quality.

I little pricey but worth it in the long run.

I use these on dubia 4x2 cages to help hold in heat and humidity cut a couple small holes for venting works great let's light in too if you don't use in cage light

This is more like actual thin plexiglass rather than the softer PET plastic. You cannot cut this with scissors or tin snips without it cracking into pieces, so make sure you use a plexiglass cutter instead.

Absolutely perfect! These PET sheets are lightweight but sturdy, super clear, and a breeze to cut to size. I used them for framing posters and also as a little pet barrier—works like a charm. Way safer than glass and way more affordable. Great value for the pack—highly recommend!

I use these curved inside my kitty litter boxes as a "back splash" to shield my walls from any accidental splashes or squirts. I did cut the top edges to round them off so I (or my kitties) wouldn't get a sharp edge. They are easy to clean and can be used again and again. I am sure there are many other uses for these but that is how I use them and I am very satisfied with their quality and the value for money. They are also very flexible so they could fit a variety of litter box sizes if you decide to try them out for that purpose.

Just what I needed!! Had the seal my crank windows for my portable air conditioner. Just had to cut to size (box cutter). I traced the screen and the hole for the large white plastic tubing. I washed and dried where the screen was and put skinny 3m tape around the perimeter to hold in the Pet sheet panel. Put window tape around the hole to seal the white plastic tubing. Good fit, not hard to cut and looks way better than just cardboard and duck tape. It’s a win for me!!!

I purchased these PET sheets intending to laser cut small paint stencils on a 50 W CO₂ laser. The listing suggests PET plastic sheets, which led me to believe they would behave similarly to polyester/Mylar stencil film. These sheets are approximately 0.04" thick rigid PET panels. Under a CO₂ laser they do not cut cleanly. Instead they soften and melt, producing rough edges and re-solidified plastic. This makes them unsuitable for precision stencil work. For anyone purchasing this for laser cutting: this is not the thin polyester stencil film typically used for laser-cut stencils (usually 4–7 mil). It behaves more like rigid craft plastic than stencil material. The sheets themselves may be fine for crafts, protective panels, or Cricut cutting, but they are not appropriate for laser stencil applications.

This is not the type of plastic that will snap with snap when bent, in fact you can bend edges into it if needed. The plastic itself can curve and roll - and will curve/not hold its weight if propped on an angle (at least by the whole sheet). The plastic itself is solid and clear and cuts pretty easily with either a heavy duty box cutter or sharp scissors for crafts. I used it to create side barrier (cut into 12"x36") for my work table and applied UV film to block out any sunlight coming from the gap between my monitors and table. At 12"x36" (half the width) it is sturdy enough to sit upright without curving as long as it's mounted properly along the length. Overall it is as advertised.

Used to cover my window for my AC. I used it above the more sturdy corrugated part as wasn't sure if it could handle a hose weight. Way better than plastic sheeting. Did 2 windows with this 1 pack with double sided velcro to secure

Génial Mis dans la porte moustiquaire pour éviter les bris de chats Se coupe super bien et fait le tire de la hauteur de la porte donc parfait Bon prix et bonne qualité

These work great to protect my french door from the dog with sepatation anxiety and protect the dog from sustaining potential injury. It is very clear so you can still see clearly theough the glass. I just adhere it with 3M strips. This time I used the velcro type in case I want to remove it for cleaning or replacement.

Good product, sturdy and fit for the space I bought it for. Would buy again