NP110 Single Stage Non-Programmable Thermostat

The wire terminals could be better positioned. The most logical way to route the wires would place them behind the temperature buttons - the ones you use are not part of the face, they must contact the actual buttons attached on the circuit board. It may be easier if you have only one thermostat cable, and not two (the air handler installer opted to add another cable rather than replacing the existing one). It was a simple install, other than the wire routing. The labels were helpful to mark the wires being used. I have found I do not need the backlight - all the settings seem to be easy to read. I would prefer that it not need a battery, but many models do. I was looking for an inexpensive replacement to our old, erratic mercury switch thermostat. I have found it to be reliable and accurate so far. It does audibly 'click' when operating, but so do many others - have not found the noise problematic. Other household items make noises as well. This thermostat displays both the set and current temperature at the same time. It also displays the current temperature when it is off. The cycle is not fine-tuneable (there is only one permanent modification available, meant for hydronic), but I have found it to cycle the system acceptably.

We don't want a bunch of complicated features. We set a temperature and leave it. No remote control (that can be hacked!), no 20 programming settings that I do not want to learn. This is simple, works right, was easy to install and.........very inexpensive.

Installed this on my electric furnace, works good. Easy to read Instructions were easy to follow. It does have a light but I would not call it a back light. You push the button to set the temp and the light comes on. Or you can set the light to be off all the time. Light stays on a couple seconds then goes out. That's good enough. Furnace cycles as it should according to the set temp. You can adjust the room temp readout to match the set temp. I used a separate thermometer and set it to match that. It was factory set but I did adjust it a little. Use a small pair of needle nose pliers or hemostats to wire it up. It was a little tricky, the wiring bar is small but it's not bad. I would recommend this.

Very simple. I'm retired. Home every day. Get up, turn the temp up. Go to bed, turn the temp down. No programming. No wifi. Wanted simple. Simple is good. If this sounds like what you want, buy this unit. Simple follow-instructions. Lit read out easy to read with my glasses at night. As for the low ratings, this was my 2nd purchase. The first works great after 2 years. As for accuracy, got to laugh. Accuracy? Is it exactly 70 deg F? Doesn't matter. When I set 70 it feels like 70. Now, repeatability? Excellent. For $20? No brainer. Oh and, hook the white wire to the W terminal, red to the R terminal,...... Easy peasy. Oh (again), I have a gas, forced air system with conventional AC.

very attractive trellises.

Works great!

I found it so frustrating to try and install that I just gave up and ordered a different one altogether. Yes, it was more expensive (about twice as much $) but so much better. This product is low budget; cheaply made and cheap-looking and was impossible (well, for me, anyway) to get the wires from my wall threaded thru the (little slot in the) back and into the body of the thing and then immediately 'bent' 90 degrees and pushed into the appropriate little holes. Not enough room to work with — I already had short wires sticking out of the wall (my problem — not the fault of this thermostat, I give you that), but I found it just entirely too "tedious" to try and get the wires fed in thru the back (pushed through a slot, but it's not big enough to allow much movement of the wires coming thru), and then 'bent over' so those wires could then be pushed into the tiny receptacles of the thermostat. So, I then went ahead and spent twice as much on another brand and got a much, Much better product (easier to read, easy to adjust and easier to wire up)! I returned this 'Emerson' one to Amazon and immediately bought from Amazon a "Model 701" thermostat. It's also single stage, non-programmable, and lighted, but oh, SUCH a better product, and SO much easier to work with!! I had absolutely NONE of the problems with installing I'd had with this 'Emerson.' I sure can't recommend this. don't be a cheapskate and try to cut corners with this thing: I say spend a little more and get a better product! Jack in Colorado

I purchased this thermostat to replace an old mercury thermostat in my basement. I had difficulty installing it for two reasons: First, the location of the terminals is not convenient. It would be best to use small needle nose pliers to insert the wires. Second, you have to be careful to mount the thermostat on a flat surface. If your wall is not perfectly flat the housing easily flexes and then the up and down temp buttons do not operate properly. Other issues I have with this item is that the flame indicator merely indicates that you have switched the heat on. It does not indicate when the heating system cycles on or off. At one point, I got an error code. However, I could not interpret the code because the instruction manual does not include the error codes. Overall, the thermostat now appears to be working and, for the price, I suppose that is all I should expect.

This is a very basic unit with no temp offset, setbacks or scheduling capabilities Note that this is factory set in °F but can be mechanically modified to show °C

Easy to connect and controls well using the mv signal from the gas fire.

Technically it is not complicated to install, but the terminal strip is small and there is not much space to route the wires, making a bit challenging to get the typical rigid 18-gauge solid wires connected properly. You will need a Phillips size 0 screwdriver to fasten the wires in the terminal strip. There is a backlight, but requires a procedure using the up/down controls to enable it. The two required AAA batteries ARE included. Defaults to degrees F, can switch to degrees C by cutting a jumper wire on the PCB.

I purchased this thermostat in December 2021 to replace the original thermostat that came with my travel trailer. The original was Coleman Mach. See picture. After replacing it, the Emerson worked excellent. I can adjust the temperature degree by degree and is controlling it very good. It is a great product and worked excellent for my application.

Very easy to install , great value