moofit CS8

I've had a Polar cycle computer with speed and cadence sensors, however the speed sensor has gone faulty and they no longer have replacements. Having used a trusted and well-known brand for a long time, I was a little apprehensive about using Moofit, especially considering the low price. Well, I'm not apprehensive any more! The sensors are easy to fit in just a couple of minutes using the supplied securing bands, which come in different sizes to cater for different bikes. Once fitted, I opened up my Openrider app (I believe it works with a number of different apps), tapped within the app to find nearby sensors, and that was it. All set up in less than 5 minutes. The sensors operate over bluetooth or ANT+ bluetooth. ANT+ is a little more accurate and power efficient so, if your phone supports ANT+, I'd suggest using that. Regular bluetooth works fine and Openrider supports both regular bluetooth and ANT+. The speed sensor attaches to the hub inside your wheel and I attached mine to the rear wheel. This also means that the speed is registered even when I'm using my indoor training, which is fantastic and something I've not been able to do before. The cadence sensor attaches around either pedal crank. The sensors appear to be very accurate and comparable to other systems I've used. All in all, I can't really find fault with the Moofit Cadence and Speed Sensor. I sincerely hope you've found this review useful. Thank you for reading.

Work really well with my bike in garage which I have sat permanently on a turbo trainer. Connects easily via Bluetooth to app I use (wahoo which then feeds into starve too). Easy and speedy to fit and good battery life.

These are definitely good value for the 2. Small box, housing both. I was impressed there there are a selection of bands to attach to the bike, so should fit most bikes no bother. Really easy to attach to the bike and appear that they should stay on well. The instruction manual is adequate for the basics. The company also emailed not long after receiving the product to provide some further advice for installation. The best piece of advice given was to wake up the sensors by 2-3 turns of the wheels. I did have some issues with trying to pair the sensors. At first I tried with Endomondo which it had mentioned and is an app I use. Unfortunately I couldn’t get it to pair (perhaps because I have the free version?) I tried Strava also, then found that Strava won’t accept it. I then downloaded 2 of the apps the company mentioned - OpenRider and Wahoo. Had no issues getting the sensors to pair with these, in fact it was fast and very straightforward and they have worked fine on my rides, though Wahoo only seems to want to use one of the sensors at a time. I have since found that both Apps ‘should’ be able to send your ride details to Strava afterwards, so i will try that out. For me, the cadence sensor hasn’t worked so well - I think it’s better suited to users of cleats. As I just wear trainers I did find that my foot would knock against the sensor when I stopped and started. Perhaps I could change the position or put it on the other side. However, for me, I think it is better suited for on the indoor trainer. Overall, happy with these.

The cadence sensor works fine but on the two rides I have used the speed sensor it has stopped working and messed up my data resulting in me having to disconnect from my watch to continue the ride

Fitted day of arrival, strapped on and test rid for 15 mins and all is good 👍 Connection with Garmin Instinct was quick and hassle free, speed seems to be correct so far as does cadence. Using this on rollers with 5 spoke carbon wheels so I have uploaded pics to show how I connected it as obviously you can't fit to a hub like you can with traditional spokes. Two rubber bands, 1 used normally as you would on a standard hub to hold the sensor in place (band A) and the other (band B) is used for lateral tension to centre the sensor in the hub/wheel to be as close as to where it would normally sit. So you start by attaching A to one side of sensor as standard; then thread A through B, then wrap B around blade while wrapping A round the outer edge of the hub, and once again thread A through B before clipping on to sensor as standard. Easy as pie and giving out good readings so far on a quick 15 min pedal. I will update once I have put it through a longer session but so far so good and very happy 😁

i have 1 set that works perfectly .. this latest set the speed sensor connects and intermittently sends data .. we tried altering bluetooth setup but we have finally started using the older sensor on my wifes setup and bingo works every time .. would send back if i could for a refund .. clearly luck of the draw if you get a good one or not

The price of this is an absolute steal. Such a great product - linked up the cadence sensor straight away and connected it to both Zwift and my Garmin Edge. Tested on both many times and all is good. Fitted the speed sensor but asbyet haven't actually taken it out to test (forgot to switch GPS off of my Edge) but its connected so don't envisage any problems. Really easy to use and to fit. I did make contact with the seller about something and they were a) very quick to reply and b) very helpful. Would recommend.

funciona correctamente

Je n'évaluerai que le capteur de cadence, le capteur de vitesse, défectueux, m'ayant été intégralement remboursé par le vendeur. Appairage rapide avec le téléphone, aucun décrochage du signal (plusieurs centaines de kms effectués avec) et le système de fixation est efficace.

Capteur Cadencé ok Capteur vitesse non cohérent : A l'arrêt il donne des vitesse 2-3km/h. J'aurais atteint 94km/h!!!! En roulant, ne donne pas du tout la vitesse réelle.

Success! I have a Peloton bike that is used for just riding. The sensors connected without a problem to the Garmin Connect app via the Garmin watch (Fenix 6s). This was done by first, by adding the sensors to the watch, (mount the sensors and peddle-they don't work standing still). Attach the sensors to the bike and start riding (30+ seconds) and the they sync without a problem to the phone; results will display in the app. I find that the results are not the same for the bike readings. Adjustments have to be made to the results (wheel diameter), that can be handled at a later time. The important thing is I get the data to display on the Indoor bike section of the Connect app - with no problem.

Om man har stora korvfingrar som gör det svårt att spänna fast gummibandet på navet, kan man karva till ett strumpstickeliknande verktyg av en blomsterpinne enligt bilden