Reserved-hole enclosure

I got this box to install a POE security camera for the house, I wanted the camera to be attached to the box in order to hide some of the excess cable that came with the box. Overall this box was exactly what I wanted for my project, it is pretty durable for being plastic and the box comes with everything needed to mount and run at least 2 cables out of it (I only needed 1). The craftsmanship of the box is really good, quite exceeding my expectations for the price, I would definitely recommend this to anyone who is in need of a product like this.There is one thing I think could be improved with this box. As I've mentioned earlier I bought this to mount a POE security camera, while I loved that this box came with 1/2" cable glands but the outside cap of the glands is just a TAD too small for a standard RJ45 connector (even without any sleeves) to go through. It is an easy fix where I just used a step drill bit to make the cap a bit bigger but after getting the cable through even when screwed all the way in there is still a little bit of space between the cable and the gland seal. I don't know if it is because I made the cap bigger but luckily where I mounted the box isn't be exposed to weather. Maybe this box isn't designed to have a CAT5 cable run through the gland but with POE stuff being very popular these days I think the manufacturer should take that into consideration.

Good box. I expected the cover to screw on but it pops on. Still it seams to stay put.

Pretty brittle and a little challenging not to damage the box trying to knock the holes out. But for low voltage pull box or termination box it works well.

Size of box reviewed: 5.9 x 5.9 x 2.8 (150mm x 150mm x 70mm).I found the material of the box allowed for easy modifications with needed holes to be drilled. The lid fits nicely on the box, with a built-in seal around the edge to keep it weatherproof. Overall, I was very pleased with the quality of workmanship and material of this project box.My project required several holes to be drilled in my box. The pre-scored 1" (25 mm) knock-outs are nice, but I needed a 1-1/8" (28 mm) hole where two of those knock-outs were located. So, I drilled a small pilot hole in the center of the knock-outs and then used a hole-saw attachment on my drill to bore the required 1-1/8" (28mm) hole (see pic with yellow hole saw). My project was to supply and distribute multiple voltages to be used by different devices. I mounted 2 ScanStrut weatherproof USB-A ports (ASIN B071WXWS9C) on the sides of the box. Inside the box, I also mounted a 6 VDC buck converter (ASIN B07SGJSLDL) and a 12 VDC buck/boost converter (ASIN B07N3QT628). From each of these converters, I will route the outputs through the cable glands mounted on the top of the box. The LeMotech box comes with 2 black cable glands, but I used 2 grey ones (ASIN B094ZDSD86) instead of the ones that came with the box. These required 2 custom 12 mm holes to be drilled in the top side of the box..This has turned out to be one of the smoothest project box jobs I have done. Hints for good results: drill holes slowly into the material, and do NOT force the drill/saw into the material. When sawing, proceed slowly so as to CUT the material, rather than BURN it. Since this project, I have ordered another one of the boxes of this same size, as well as another in a smaller size, for use in other projects.

This is a light gauge, clean and attractive plastic box, probably well suited for a project box or control box for indoor use. Definitely not suitable for a rugged or structural application. I had need for an outdoor box to bridge between two metal conduits. Too flimsy. Sent it back.

This junction box is nice but the top does not have screws to keep it on. The top snaps together instead of being screwed on. It does seem like a good fit but I worry about weather changes and how well the top will stay securely together. I’m sure there is a place for this particular junction box but it does not meet my needs. Product was returned.

I like the waterproof cover. the size was just right. The plastic makes it perfect for different applications.

Installed with low voltage switches and wiring. The multiple pre-stamped holes for installing the wiring are perfect for routing the wires to the box. Highly recommended.

Très satisfait rien de négatif à dire.

Just what I needed ! Good quality

I used this as a junction box for a 4 conductor, 4 gauge connection. The 1 inch NPT glands just fit the cables i was using. The wall height is only about 2 inches (50 mm) so after drilling a1 inch hole in the side, there is only about 1/2 inch of support material. With these fairly large cables considerable stress is placed on the sidewall of the box. If I were to do this over I would choose a box with a taller sidewall - maybe the 255 x 200 x 120 box instead of the 200 x 200 x 80. Also I never used the stoppers. Not sure what they are for other than covering a whole you already drilled.

I like this junction box. It seems to be made from good materials.

Good qualiy