VEVOR Electric Hoist 1760lbs with 14ft Wired Remote Control, Electric Hoist 110 Volt with 40ft Single Cable Lifting Height Motor, for Garage Warehouse Factory

VEVOR 1320 LB, 120V ELECTRIC HOIST. A+! Works great! I highly recommend it. Easy to install and operate. Comes with both wired and wireless remote controls. Has safety shutoff for winding winch in. Includes everything needed to start lifting right away.

This hoist saved my chimney brick project. It worked as hoped and carried all the bricks and morter two stories up.

Simple to install, albeit a little awkward but that’s just unavoidable. Worked right out of the box and I used it to pull a deer out of a truck and hang it. Did the job no problem! Pay attention to the size/length of your lag bolts to get the most weight capacity out of the winch.

Been using this for about 4 months now, using it to install and remove a custom pickup bed on a Mack tractor. The operation is pretty good, with plenty of cable to do double lint lifts, which is needed to slow it down.. it. Could actually be slower for better accuracy when aligning lifts. The remote is a huge plus allowing free motion, even below the truck while aligning the lift. I have never actually used the tethered control, even this it is of good length with the hoist at a 12’ truss level. Over all a good lift for the price.

Winch worked great and was easy to install.

Excellent value. Used for basic tasks like a deer hoist. Seems good quality.

I bought one of these winches a few years ago. Works well so far, I use it to store my 5th wheel hitch up in the overhead of my shop. It only gets used when removing or reinstalling my 5th wheel. It is a little noisy but that is to be expected on a winch in this price range. So I bought a second winch to put on a rail in my shop. Surprisingly enough it is somewhat quieter than the first one and seems to function OK for what little I have used it. My problem is with the poor final assembly of the winch. Photo 1 - One of the welded on nuts used to install the hanger brackets on the winch was welded in at an angle. Photo 2 - The spring, washers and safety stop disc (Red Arrows) were assembled on the wrong side of the swedge. In this configuration the traveling block cannot be used. I removed the swedge, positioned the parts on the cable where they should have been and place a clamp where the swedge was and put on the traveling block. Photo 3 - The washer was the wrong size to keep it from being dragged into the traveling block. Fortunately I noticed the problem before it was under load or it would have damaged the spring and other parts. (Red Arrows) Photo 4 - I cut the end off the cable, removed the lower washer and replaced it with a fender washer (3/16" X 1 1/4") so the hoist stop would not bind with the traveling block and allow it to operate as intended. Then I put 1/8" cable clamps were the swedges had been. Evidently they don't do much for final inspection on these winches before shipping them. These were problems that should not have happened and if they did, they should have caught them prior to shipment. If I had used it like it was delivered the safety stop would not have worked as intended and likely damaged the winch or winch parts.

This was the heaviest item I ever ordered. It took two men to deliver it and I had to push it thru the door. It is of fine quailty but as I said very heavy. It should hoist anything. Given as a gift and well received.

Posizionato al primo piano, è ottimo per salire e scendere bombole di gas da kg. 25. Solido, affidabile e facile da maneggiare

Funciona genial

Convient pour moi

Habe mir damit einen Dachziegel Aufzug gebaut, Fernbedienung funktioniert einwandfrei. Top gerät zu absolut kleinem Preis. Nach der Dachbaustelle wird es als Lastenaufzug im Hausverbaut, man wird ja nicht jünger.

Parfait pour ce que j'en attends ! Il me sert pour un monte matériaux dans mon atelier depuis un an et c'est nickel!