hunhun 20-Pack 3.3ft/1Meter V Shape LED Aluminum Channel System with Milky Cover, End Caps and Mounting Clips, Aluminum Profile for LED Strip Light Installations, Very Easy Installation

Better then expecting. It wasn't that easy to install especially with the screws as soon as I was installing one the other side was was falling down until I had few hooked. V shape that hold aluminum I hope it was holding better and I understand you made it so is not visible but so far after installing is ok and not falling down. I regret didn't put the corners to hold and make it more sturdy but I think I will be ok without it. The milky cover fit nice and will give a nice look but you can still see the led light dots so it will not give you an neon effect. So far I am very happy with the quality and accessory that was supplied. I wish they had some kind of instruction on how to mount. My kid love it.

Installed these on a new staircase. Fitting the plastic diffuser into the aluminum track can be very frustrating if the track is not installed perfectly straight. The part of the track that the plastic snaps into is very small and leaves little room for error. I had to remove a couple, more than once to get the plastic to stay in place. Mainly my fault for rushing and installing as I was installing stairs at the same time. If you have the room to slide the plastic into the track instead of snapping into place you would be much better off. As far diffusing an LED light strip, just like most other diffusers, not so much. I tried adding sheets of parchment paper to see if it would help. No luck there. Lights were still too bright to not see each individual LED. A frosted glass spray may help but, wasn’t sure if it would start peeling when bending the plastic to install to track. If you are going to have the lights dimmed or just as background mood lighting probably not a deal breaker. Overall I think it’s a good product for the right situation. No missing parts, aluminum track was straight and of great quality for the price. If you are able to slide the plastic into the track, install at an angle where you’re not looking directly at the diffuser, these should work for you.

I've uploaded a pic of what you would see if you're using LED light strips with a density of 60 LEDs per meter. You can still see the individual pixels. Looks like you'll need 144 LEDs/meter if you want it to just be solid light. These are the lowest priced corner mount LED strip brackets I found on Amazon. They look exactly like what you see. It came with the aluminum bits, the covers, 4 corners and mounting brackets. Now there are 2 different style of mounting brackets, one is a small 'single' clip and the other is double or maybe triple the width. You only get 4 of the thick ones and I really wish I had a lot more. To fit the aluminum into the brackets you basically place one edge on the bottom of the clip and lever it into place. That means that the brackets will spring a little. Which means if you place the brackets tight to the corner of the wall you'll have an almost impossible time getting them in - leave a little room. And give up on the small brackets, look for those thicker ones - they are what you want. With the wide mounts you can place 2 segments end to end and they will be guaranteed to meet perfectly together. Using the smaller ones it is really difficult getting things to match up due to the natural curve in the walls that happen over time. I have to say, with the LEDs turned off it looks really good - you don't even notice you have something up in the corners, it blends in like typical molding. When they are on, the individual LEDs are noticeable even at 60 LEDs/meter, but they come through the milky cover very brightly and I don't have any complaints about that. Bottom line is they will really make your room look 'finished' and more professional. As long as you are patient and work slowly to make sure the ends will meet up. But even when they are put up fast and dirty and look like a hot mess upon close inspection like mine, they still look better than bare LED strips.

I didn't read the description very thoroughly and wasn't expecting the brackets to be metal. As such I had to use an angle grinder to cut pieces, and while easy to install the whole process took several hours to complete. We also tried using a hand saw to cut the metal but it left the edge warped and bent out of shape and unusable, so I would recommend a power tool if you can afford one or borrow one. Otherwise this product will not work for you if you need an exact measurement. I used a double sided foam tape to install instead of the screws for a more renter friendly installation, and they seem to be holding up just fine. This also really helped with uneven walls, and I could just layer the tape to fill any gaps. I would recommend getting LED strips that have a higher bulb count than what I used, but I'm satisfied with the result. I was able to hide any gaps between the metal brackets by installing the acrylic diffuser strip past any cuts, and this created a seamless, continuous flow, and hid the gaps. (As pictured) This really sped up the process as I didn't have to worry about installing the brackets perfectly level or flush to each other.

LED lighting can be tricky. One constant issue is the lights staying up where you place them after they have heated up from being turned on for a while. The sticky tape that comes on most led rolls is good, but weakens with heat. Putting the LED onto these aluminum strips gives a perfect surface for the lights to stick onto. AND the diffuser covers work to keep the LED from falling out of position even IF the tape lets go. That leads into a second issue with LED lights. Heat. A major cause of LED failure is the LED strip heating up over time and burning out the diodes. Either by total failure, or more frequently, lowering the intensity of light available from the LED strips. Applying them directly to the aluminum strips acts as a heatsink for the LED. Enough to help extend the serviceable life of the LED strips. Not gonna lie, it is a tiny bit of extra work, but for a much better result and longer stable lifetime I would fully recommend using these or a similar track system for your LED lights.

This corner molding with LEDs inside make our game room finished. great product and put it all around our game room. Easy to work with locks into place easy and looks very professional after installed. Easy to cut easy to install we love it thank you. We used a Dremel with small cut off wheel the cut the material with. We also purchased the extension connectors for the V shape LED aluminum channel system. The channel system that we used were the 3.3 foot with milky cover. Items come with extra screws and fasteners very great product easy to use. Very friendly staff to work with. Thank you hunhun. Steve in Wyoming

These worked perfectly for putting some LED light strips in the hallway of our basement stairs. They were easy to hang and assemble and fit perfect in the crease between the wall and ceiling.

I should have read through reviews of this product more thoroughly. The material they supply you to diffuse the lights is terrible it looks almost exactly the same as if I'd left them uncovered. The cover is also not easy to apply. This company doesn't offer enough variety if sizes for whay they're needed for. 3.3 ft is what I had to make work because other sizes weren't available at a decent price. I save money buying 60ft of 3.3 peices compared to 60ft of a larger size they charge way more for. I only bought these because of how little of this product is actually available anywhere.

Channel looks ok but missing hardware and could not contact the seller to get the parts delivered.

Used this l to light up my stairs with WS 2812 LEDs. It looks great.

Excelente producto

Got this product exactly on time and took a look at it. Looks and feels promising, easy to install, handle etc. However, one issue...lack of instructions. It is kind of an intuitive product to use, but i just feel like a user manual would not be a bad idea to include in the packaging. I happen to be one of the "non-smart" customers that had to actually look up proper installation for it. But everything else is good. I would recommend