House Tuning Roll Bar Mount Clamp, 2.0 in Tube Clamp for Light Bar (2 Pcs)

Perfect fit for my Xterra. Got lights and flag installed on them. Sturdy and strong. Definitely recommend

I went through all the reviews listed here and could not find anyone asking about an oval cross bar or mentioning that they havel one... I saw round and square though. I mean an oval Is kinda like a Circle... OK maybe not but still. I have a 2020 Subaru Outback and I will be mounting some LED roof lights to the cross bar, seeing as these are not expensive and looked decent I decided I would go for it and be a test subject. Pros 1.) Build Quality is very nice and solid. 2.) Coating looks like it will hold up to the harsh elements nicely. Cons (For My Application) 1.) Weight, I think that in this application weight might be your enemy, I don't see them staying put with to much weight since they are not completely grasping the bar itself. For the small lights I plan to use it should be fine. 2.) Obviously the shape is not the same, oval vs round means gaps. Does it look bad, no. Does it look good, no. I feel like in day to day use no one will notice this minor con except for me. These might be a temporary solution until I find something that will work better for me, until then these are just fine. However, I do hope this helps someone with the same or similar situation.

I bought these to mount a shovel and traction boards to my 2019 4Runner. The 2" size is a bit too large for the factory Toyota TRD roof racks rails. I tried using inner tube rubber to make up the difference but that did not work out. The next day I bought a piece of 2" round rubber hose from the plumbing dept , I cut some slices off to match the width of the clamps to make up the difference in size and it worked fantastic. I then drilled 2 holes in the traction boards, ran a 6" carriage bolt through the clamp and 2 boards and put a nut and a threaded knob on the outside to ensure that they would not loosen up on the road. The other side has rubber adaptors to hold circular tool handles and my shovel is secure. Good deal, Recommended highly. Well made with a low gloss black crinkle coat.

These clamps actually fit a 1.75” bar as advertised, unlike the Nilight ones. They are sturdy and easy to install. I’m using them on my tube bumper for mounting my offroad lights. My only complaint is that the first few threads were damaged on two of the bolt holes, which is why I removed a Star. I had to re-tap some of the threads to get it to hold.

I have a 2.5" guard on my vehicle and wanted to mount items to. I orders the setup for the exact size needed and was confident in the purchase. Upon test fitting the clamps, it was clear that the rubber spacers provided did not allow for a complete seating of the clamp. I consider complete seating as to be 100 secure while closing gaps between the upper and lower section of the clamp. (Flush and clean install) To achieve the perfect fit, I had to cut away the rubber seal on the two sections until there was a strong hold that barly allowed the sections to touch. This was not a difficult process and the end result was professional in appearance and secure. Top notch product if you take the extra step or one could simply use as delivered and leave large spacing between the sections.

I bought these not for light mounts, but to go on the lower front control arms of my Jeep. The aftermarket controls arms did not have a threaded stub to hold the ABS sensor wires. I used these in roughly the same spot and just bolted the ABS sensor wire tabs to this with a separate nut and bolt.

These brackets are well made but are way too light for my application of mounting 4” light pods for off road use. They never would have held up over time. In addition, the purpose was to mount two 4” light pods onto the back of my Rocky Mounts Roof Basket. The diameter was not compatible and no matter what I did, would not fit. I ordered a heavier set of brackets from a different brand using shims and a piece of inner tube inserted in between the rack and bracket and fixed all issues.

Good quality and worked well.

Really surprised at the quality. I used them to mount a nice fuel filter setup. Probably overkill for my application but they look cool.

Gran opción para colocar accesorios sin necesidad de perforar

very high quality prduct perfect for what i needed

As described. Good quality