WiFi 7 Wireless Access Point BE11000 | PoE + or USB C (not included) | 2x 2.5Gb Ethernet Ports | Triple Radio | Nebula Flex Cloud or Standalone | RADIUS Authentication | TAA Compliant | NWA130BE

Set up was easy. Multiple SSIDs and VLAN tagging work as expected. It's a simple, powerful AP that lets my 10+ year old OpenWRT router keep doing its thing while giving my network clients modern speeds. The only two snafus: Firstly, when running off PoE, it didn't recognize that my TP-Link Omada injector was capable of 30W so it was running in "low power mode," but there was an override setting to fix that. Not sure if the problem there was on the AP or the injector. Secondly, I only have a single WiFi 7 (6GHz) client, and it is off most of the time. 6GHz APs aren't allowed to broadcast that all the time and they rely on clients discovering them via a 5GHz network first. I haven't quite figured out how that works, so the most consistent way to get my desktop to connect on 6GHz is to reboot the AP after the desktop. Again, I don't know if this is an AP problem or something with my Linux/NetworkManager/iwd/device firmware stack. (I would bet NetworkManager...) But overall, it seems pretty great. Between a Wifi 7 (6GHz) client and a 2.5Gbps wired client, I'm seeing ~2.35Gbps of payload data throughput with iperf3. Between that same 6GHz client and a Wifi 6 (5GHz, 160MHz), I'm getting 1.25Gbps. Energy consumption from the wall (again, using the TP-Link injector) is ~12 watts at "idle" (~20 clients connected, between computers, phones, tablets, and IoT) and ~17 watts when running those iperf3 tests. There is a manufacturer supplied OpenWRT build for this NWA130BE, though I haven't used it yet and don't intend to until it's better documented/tested. The fact the manufacturer published a build at all is promising, though.

We're using it in a small home, and it reaches where we need it. The handful of Wi-Fi 7 devices we have seem to like it; the older devices also perform well. It works great with VLANs, allowing you to segment your network appropriately if your router supports that. The passthrough port does not support Jumbo Frames, I learned that the hard way, but both ports, uplink and the extra, are 2.5 gbe, and with a POE switch or injector, it makes for a clean installation. If you use the Nebula cloud, it offers a quick setup, and it also supports local administration. The range was better than expected, there's one small corner at the opposite side of the house where some devices can't decide if they want to try high speed or just a solid connection and they sometimes drop a few times while they figure it out, but that seems to be device-side programming because if you pick an SSID that only has 2.4 Ghz it pops right on. Compatibility, this has been great on this AP, but a massive issue for us in the past, from cars and other IoT to laptops, tablets, and phones we'd often get a complaint from a device, none have done that yet after I figured out the downstream port doesn't do jumbo frames (blocking a resource many of my devices needed) and fixed it. We run fewer than 100 devices, but in that vicinity on it in our house, and I'd feel comfortable deploying this in a small office, probably in a 3-pack. I wish they had these when I worked at a small-town MSP.

**update 9/19/25 Does not seem to support wifi-7 even though it is advertised as supporting. Multiple clients are also connected to the access points and they do not show as clients in the software as connected. Wi-Fi speeds will drop off if you’re not in the same room. Same room speeds are great; however, you will have random disconnects even when in the same room. Looking at the log reports, the reasons will vary. Some occur every day at the same time and the reason given is simply Netconf connection is disconnected. Luckily, the reporting aspect is great on this, it really can be useful to see what’s going on with your network and devices. A lot of information can be obtained from the free tier of access. While that can be expected for devices like this, certain things like exporting a report require a paid license. Which is silly IMO. The iphone app is dismal and very limited in what you can do with it. I rarely use the app as a result. You will need to go to the website to really do anything of value for settings aside from obtaining basic information. The website can be a little difficult to figure out as figuring out at first. Once you get the general understanding it’s very informative. It will tell you everything you need to know about the network, devices. If you do not know much about Wi-Fi or networking, I would suggest you research what terms mean before you go change random settings here. The site does a good job of offering help as to what things mean or do as well. I would never consider this brand a professional setting; it struggles in a home environment with around 20 devices. If I wasn’t past my return window I would ship it back.

This seems to be a good AP, essentially a highly flexible, enterprise grade AP at a home price. I had no problem setting them up in Nebula. It took longer to setup my account and org than to setup the first SSID and AP. Nebula is a bit clumsy about how it logs in - it doesn't adjust well to small screens - I have to use my tablet (10.3") to see the button to add the AP. I know that a lot of people complain about no power supply - read the description - you have no reason to complain. For the record, an enterprise AP doesn't come with a power supply either. You can use any 12v 2a power supply from the hundreds that are all over Amazon or get a power injector. My next steps are to add an SSID just for IoT devices, VLANs to isolate my IoT network, and LAG to use both LAN ports. From there, I will just play, especially in the local web and command line interfaces. To hit the tags: Signal Strength is good (please note that 6GHz penetration of walls is worse than 5GHz - not Zyxel's problem at all), reliability is good so far, and the speed is certainly good (my ISP is the bottle neck, but I can get speeds FAR better than my old Wi-Fi 5 Orbi. Maybe I will set up iPerf and see what I get internal to my network). Overall... it's an easy decision... buy it. UPDATE: Works great with the POE+ injector from Zyxel.

There is another review here saying this unit only supports WiFi 6; that is false. I can confirm this unit produces WiFi 7 802.11be which I was able to connect to with WiFi 7 clients. It works fine. It has 2.4ghz 5ghz and 6ghz radios, all of which work well. Speeds are as expected. The unit is nice looking. 2.5gbe Ethernet ports are nice. The ap has two ways to set it up, cloud based and local administration web GUI. I choose local and it was fairly rough. It's a perfectly serviceable GUI but you really need to know what you're doing and it does not hold your hand at all. I can't comment on nebula cloud. Either way, this isn't a consumer device. That's why they expect you to power it with poe and as a result it does not come with a 12v power adapter. I had to buy one separately which was fine. This is an enterprise device that consumers can use if they are savvy to get cheap Wi-Fi 7. It's great for what it is, just realize what it is

Hardware Performance vs. Firmware Stability: I’ve purchased three of these NWA130BE units so far, and the experience has been a rollercoaster. On my very first unit, Nebula requested a mandatory firmware update immediately after registration, and it bricked the device. No recovery was possible. I am a power user and even attempted a rescue via TTL cable to access the console, but the unit was completely unresponsive. I had to go through the hassle of a replacement right out of the box. Documentation is a "Time Capsule": The biggest issue with Zyxel isn't the raw speed (which is great once configured), but the lack of modern support. 1. Outdated Resources: Most official support articles are 6+ years old. Trying to find specific solutions for a 2026 WiFi 7 flagship using documentation from 2018 is unacceptable. 2. Community Dependent: You are basically on your own. If you hit a snag, your only hope is searching through forum threads, as there are very few independent technical reviews or updated tutorials for this specific model. 3. The Nebula Learning Curve: Unlike UniFi, the interface is not intuitive and the curve is steep. There is no local controller option, and many features that should be standard are locked behind a licensing paywall. The Bottom Line: When the AP is up and running, the WiFi 7 performance and 2.5GbE backhaul are impressive. However, the risk of a bricked unit during a standard update and the severe lack of updated technical documentation make this a hard sell for anyone who isn't a networking expert. PROS: Excellent signal and WiFi 7 speeds. CONS: High risk of firmware failure, poor documentation, and a clunky management interface.

Works great with my 2Gbps home fiber service. Remember if you're going to use POE+ for power that you need POE+ (not just POE) and a POE+ injector that is rated for 2.5Gbps if you want to get full speed out of this unit. I'm using this AP with a Zyxel USG LITE 60AX router and that combination works great. One downside I can't get MLO to work. My Wi-Fi7 card in my PC is MLO rated as well as this unit. Don't see any specific feature to enable MLO in the configuration settings.

Best ap I have ever used...speeds are highest I have seen. Supports many clients...very nice product. To add I have used home routers as AP's for many years now because they provided the best speeds. This purpose built AP is better than any of those I have used so far and the price is amazing compared to all the new 500 dollar plus routers coming out. This AP runs all my stuff with no issues every different standard. You can have SSID's for each standard and for each vlan you want it's so nice. The RF is strong and goes far I can't say enough about this product. it's impressive.