4 Pack Hall-Effect Joysticks Replacement for DualSense PS5 Controller, 3D Analog Sensor Wheel Thumb Sticks Joystick Rocker Module Replacement for PlayStation 5 Controller

I have fixed 4 controllers with these and they work great. I had a little trouble with 2, the push down buttons were not working, but I realized it was my fault and not the product. When removing the old sticks it is very easy to pull the sleeve in the board off with the stick. As a fix I had to push more solder in the hole to make the connection. The tweezers really helped with that task. I have also tried the TMR and I like those a little better.

Used these to replace the joysticks on my PS5 controller. I have only used 2 of them so far but I am keeping the other 2 for when my other controller starts to drift. They are not easy to replace but that is Sony's fault. These fit the control board perfectly and work great so far. I have not checked the calibration or anything but I don't have any issues playing any of the games I play. There is an equal amount of dead zone in all directions as far as I can tell and no more drift or ghost inputs. The kit is nice and helped. I didn't use the joystick caps, I like the ones that the controller had originally and these feel a little harder and more like plastic, but it's nice to have extras in case I ever need them.

works ok, makes it a little more touchy though so you might want to lower your sensitivity after

these sticks are decent for what they are but they have over range issue giving me an error rate of 10% and this cannot be calibrated out they include these shaft wraps and u need to use 2 on each stick to get the circularity to be even and get the error rate down to 5% but that ruins the feel and make them feel sticky i would not recommend these are definitely the ginful v5's stick more like v1's the 8% is with the wraps and the other is without

the sticks worked at first but now it has started drifting after one week. low quality product that is breaking down fast.

I bought these hall effect joysticks to permanently fix the drift issues that started showing up on my PS5 dual sense controller. I am very happy with how they perform now that the original joysticks have been replaced with these hall effect sticks and the controller has been recalibrated. But a word of warning- this is not a simple or easy fix. If you do not have experience or the equipment to do solder rework you will most likely have a very hard time replacing these sticks without damaging the controller. I would consider a hot air rework station imperative for this operation as the solder is that horrible RoHS stuff that only melts at temperatures approaching the surface of the sun. If you do not have the equipment or experience I would recommend the much easier fix of simply swapping the wiper guts on the existing joystick potentiometers. It is a much easier task and will get rid of drift for another couple hundred hours. After either fix you will also need to recalibrate the controller with 3rd party diagnostics run off of a computer. If you have the tools and the knowhow I would definitely recommend buying these replacement joysticks to permanently fix your PS5 controller drift issues.

Work as expected for a PS5 controller that was previously experiencing drift. 3 of the 4 would have been fine with no calibration, but one was drifting slightly in game play. Went online and calibrated them on DualShock/tools.github.io. A few other reviews had mentioned issues with their R3. In my case, no issues with my L3 or R3, they still work fine. Removing the existing hardware is a pain, in part due to the number of pins involved and the fact lead free solder requires a higher temperature. After spending too much time trying to desolder ~14 pins and remove as a whole assembly, I ended up breaking it down into smaller parts. For example, disconnected a pot and removed just those 3 pins. Much easier doing it in small steps. Once I got the hang of that trick, the second (left) one took half as much time as the first (right). A nice small flush snippers, desolder braid, and flux are the accessories you need - in addition to a soldering iron and solder. If you don’t know what those are, then this project probably isn’t the one for you.

Just finished replacing all 4 joysticks on both of my controllers and right out of the gate, they work great. I highly suggest plugging your controller into your laptop and calibrating it at https://dualshock-tools.github.io to ensure you have it centered properly (very easy process). If you dont have a soldering workstation, you will need to make sure you get the essentials before attempting this replacement. It takes a moderate amount of dexterity and know-how when it comes to removing the old joysticks, desoldering, and soldering in the new components. I wish I had a desoldering gun for removing the old joysticks because using a focused heat tool and desoldering wick was a biznatch. At minimum get yourself a desoldering gun, a soldering iron, solder, and flux before you get started. Doesn't hurt to have some 90% or higher alcohol available to clean the circuit board if needed. Great product thus far, hope it holds up and myvcontroller drift stays a thing of the past.

Excelente producto, repare mis controles y nuevamente a jugar!!!

Fit perfectly, work better than stock one, but need some technical skills and a soldering iron to replace.

All four joysticks I installed worked after I calibrated them online at dualshock-tools.github.io. However, they did not perform well initially in the circularity test and required lots of tweaking using the online tool's custom range calibration. Also, while the L3 & R3 button clicks worked, I find them to be too sensitive; I often accidentally click down on them unintentionally - I do not have this problem with standard PS5 or TMR joysticks. I had no problems installing these joysticks, you get lots of extras with this package, and you won't need to ever worry about stick drift. However, they do not calibrate well and L3 & R3 button clicks are too sensitive for me. I recently installed Aknes TMR joysticks and find them to perform much better.

Very poor modules. I installed them and the sticks dont actuate correctly. Both sticks very slowly return to center after you move them. It takes about 1.5 seconds for them to return to center. Worse of all, one of them still have drift. Even after calibrating them several times. I would not recommend these.