GAMDIAS AURA GC2 ELITE ARGB ATX Mid Tower PC Case, 4 x 120mm ARGB Fan, High Airflow Mesh Front Panel, Tool-Free Tempered Glass Side Panel, Black

Good quality case, plenty of space inside to fit gpu. Back panel is offset a bit helping cable management. Highly recommended case

It's a nice case overall even though the fans are a little noisy . Great cooling and a nice RGB light show the only problem is that you are very limited with hard drive space . I managed to fit a cage for extra SSD's as there is plenty of space .

Good case and quiet fans considering their not brand name

3 out of 5. Would not buy for full price but with discount it's kind of ok for the price. Three things that I did not like. Included fans are SATA powered and daisy chained. Reset button has proprietary plug connecting to fans. 5V ARGB plug in the case connecting to fans that I've bought did not work.

Don't buy the case for the fans they don't support speed control. You also lose t the case reset switch to ARGB control

Case seems good for a budget but unfortunately arrived and the back panel was bent. Don't have time to go through return process.

This is a very nice looking case, especially for less than £40 in the sales. However, a couple of problems came up and I have knocked off one star for each! The worst problem is the lack of instructions and more precisely, the lack of labelling of the screws. There is a pack of black screws including the sandoffs for the motherboard, large head screws presumably for the PSU, and a bunch of round headed black screws. This is when they should have instructions or the screws in labelled packs! There are actually two types of these round headed black screws but being completely black they all look the same unless you look at them extremely closely! Even if you spot the difference it's still up to you to guess what they're for. Problem is, if you use the wrong screws to attach your motherboard to the case you will not only destroy the threads in the standoffs but the screws will be half way in before you realise your mistake. Then when you try to remove the screws they are pretty much welded to the standoffs by this point, and you will only succeed in unscrewing the standoffs from the case below the motherboard. From there you can only hope to eventually free your motherboard from the case with all the standoffs dangling below, still attached to the 'wrong' screws and then use a pair of pliers the finally remove the standoffs and start again, this time with the other type of screws! That's what happened to me anyway. The 2nd problem was that even though the holes in the glass panel appeared fine when the case was received, but the time the PSU, motherboard and all other components were installed, somehow the whole case had shifted and ony 3 out of 4 screw holes in the case matched up with the holes in the glass. Final small problem, the USB slots on the front of the case are so tight it's extremely hard to remove the USB plugs again!

It's a solid case but misses out on being 5 star because of a few niggles! The Pros: Great looking case, tempered glass side panel & built with plenty of cooling options. Big enough for an ATX board with enough space for some of these monster GPUs you can get. Comes with 4 x RGB fans. 3 on the front & 1 on the rear. They run off a SATA power connector & pressing the reset button on the case allows you to cycle through a few colour choices. You also get ports on the top that plug into the mainboard (2 x USB 2.0/1.1, 1 x USB 3.2) Along with headphone & mic port. The Cons: The Reset button is used to control the Fan LEDs!! Yeah, dumb. Took me a while to figure out as I was looking for a reset switch header to plug into the Motherboard! Power LED +/- are separate instead of being wired into a single double block so lots of faffing about there (HDD LED is wired into one block so go figure!) POWER button header didn't have +/- symbols printed on the single block so 50/50 chance of plugging it in correct first time round. Rear LED fan blocks the Back Panel on the motherboard so had to remove it get the board fitted correctly. No replacement PCIe panel slots so if you break one off to fit an expansion card and then remove said card, you're left with an ugly gap on the back of the case.. more if you end up using multiple expansion slots and end up taking them out. Overall, It's a good case. Fans are super quiet, plenty of cooling solutions to stop things getting toasty. I will be replacing the fan at a later date as the current ones have no speed control so they're 100% all the time! Good value for money though.

Great case, tonnes of airflow. Allows for great cable management. Hidden psu. Room for 2 fan water cooler up top.

ماتوقعت الكيس يكون كيذا ، كبير مره وتبريده وشكله رهيب بعد ورخيص جدا اخذته ب ١٨٠ على ما اتذكر مايجي معه ريموت لكن في زر فيه تضغطه يغير لك اللون من كم ١٠ الوان وتقدر تطفيها بعد ، للامانه ماتوقعت بلاقي جوده مثل كيذا فيها

Très beau boitier bien fini, 4 ventilateurs LED. un bouton pour varier les couleurs, Une grande carte mère et carte graphique rentrent parfaitement y compris ventirad double ventilateur jusqu'à 160mm de haut. Manque juste un fil connecteur pour le reset mais ça n'a plus vraiment d'importance maintenant.

安いケースでargbファンが4つも付属は破格すぎると即購入。 安いメーカーによくあるネジ穴が歪だったりパネルはめるのに苦労したり裏配線スペースがほぼ無いみたいな構造の欠陥は無く 有名メーカーと大差ない作りで満足でした。 が、argbが4つと言いながら他のレビューにもある通り4つの内の一つだけargb端子が付いたファンがあるだけ しかもその一つも自分のファンではどんなソフトを使っても制御不可でずっとレインボーに光るだけでした 残りのファンは全て電源ケーブルのみで電源が繋がるとファンが回りビカビカ光るだけです。これも写真付きレビューと同じです。 総評で言うとファンに関してはほぼ詐欺ですが、ファン無しのケースのみでも十分破格なので★3です。全然満足です。

Preis Leistung top. Gute Kabelführung. RGB nur über Taste am Gehäuse steuerbar.