ELEGOO PLA Filament 1.75mm Marble 1KG, 3D Printer Dimensional Accuracy +/- 0.02mm, 1kg Cardboard Spool (2.2lbs) Fits Most FDM 3D Printers

Best Quality Filament And Role Stand

Really high quality! Go for this if you care about print quality.

I have printed this with 220°C nozzle temp & 70°c bed temperature. The result much better than my expectations.

The prints turned out well! Have already purchased 3 rolls of filament. Will definitely purchase more

Very good product

The filament quality is good. Received the correct colour as well. Cost is slightly on the higher side.

The filament isn't properly spooled. Caused a failure in 3 prints as I thought the spooling issue was a single occurance. Likely that the entire spool is bad. Not sure if elegoo is sending sub-par quality to India, but this definitely wasn't the quality when I was buying their filament in the US.

This filament is the worst quality I have ever used. There is debris inside the filament (pic attached) and the uneven thickness is just a pain. Ruins prints, terrible adhesion, absorbs moisture like it’s a diaper. Buy ANYTHING else.

I sacchetti sono un poco piu rigidi degli altri, sembrano di qualitá leggermente migliore. La pompa é piccola, compatta, si ricarica con usb-C, non é rumorosa, ed in un paio di minuti mette sottovuoto tipo baccalá il filamento. Non necessita di un piano d'appoggio libero per lavorare, la valvola è a senso unico e non necessita di essere aperta e chiusa. E'molto pratico, pulito, funziona esattamente come nemmeno osavo sperare funzionasse. Sono molto contento. Non dico niente su ipotesi di durata nel tempo ecc. Mi sembra un articolo economico ma ben fatto.

Filamento excelente

Immer super Filament, läuft immer zuverlässig mit super Ergebnissen

Das Elegoo Vakuum Set ist meiner Meinung nach das Beste. Es kostet bereits etwas mehr als alle anderen der Konkurrenz, wie Creality z.B. aber ich garantiere euch: Die Beutel sind von spürbar höherer Qualität! Die Pumpe an sich funktioniert zuverlässig ohne grossartiges Gefummel oder Zwang erst den passenden Aufsatz drauf stecken zu müssen.

I bought a spool of ELEGOO beige color for a project. It started off with a couple MAJOR issues with bed adhesion: after small successful tests, I ran the large main job. over halfway through, parts detached from the bed mid-print and collided with other parts, knocking them loose and ending up with a huge spaghetti tangle. I lost a distressingly large amount of filament on that failure - I didn't weigh it, but I estimate nearly half the spool. I'm contacting their support line in hopes they'll help replace the lost material somehow, since their suggested bed temp range didn't work at all. (I'll update with how their service is.) I did some trial-and-error adjusting on the suggested bed temps, and lost some more material in the process. I'll have to look back and see what temps I ended up with, and edit this review to add them in case it helps anyone else. After the temperature adjustments, the project printed impressively well. Smooth matte finish, minuscule layer lines, and a nice beige color tone. After the unfortunate waste from the first failures and the finished main project, I decided to print another small detailed project with the leftover filament. I purchased an .stl model of the gargoyle candelabras in Disney’s Haunted Mansion “stretching room”. The last two pics are the originals in Walt Disney World, for reference. (The 3D model is by SERGIMEN3DART on cults3d.) I fired off this smal-scale version before committing to a full-size print. The model is split into 7 parts. I printed them at .10 layer height on my Prusa MINI+. They came out waaaay better than I expected... especially at such a small size! It's about 160mm wide, total. I quickly removed the support material and dry-fit the parts together. No other post-processing has been done. With a couple birthday candles clutched in his fists and an appropriate perch, he's ready for some pre-paint review pics. The details are sharp and clean, and the layer lines are almost invisible to the naked eye. I've still got to do some light cleanup, then prime, paint, and weather him up. He'll be a perfect lil watch guard, sitting on the shelf above my desk to keep an eye on things and ward off bad vibes and evil spirits. ;) I'll definitely be buying more of this filament. Just gotta decide which color I could use next....