PLASMA CUTTER

Very pleased with the initial results. I made several cuts on 10 gauge CS sheet and 1/2" CS plate just to see how well it cuts. I was pleasantly surprised, especially with the 1/2" cuts. The air regulator is set at 65 psi for both materials. Control settings were at minimum for the 10 gauge and maximum for the 1/2". More testing to do before I'm completely satisfied, but for now quite happy. A good plasma cutter at a great price.

Bought for a food plant, where everything we do is stainless steel. Got tired of cutting everything with an angle grinder. Stainless steel takes almost twice the heat as mild steel. For $200, this performs as well as the $2,700 my last job had. I’ve had it for a month and used 3-4 times a week, normally on 3/32 or 1/8” sheet metal. Will cut both on 110V, roughly 25 amps. Getting up closer to 35 output amps, it will trip our 15 amp breaker occasionally. But on 220v input, it cut 1/4” steel no problem. Roughly 55 psi input. The ground lead that it comes with has a thin cable and is short, but it’s a dinse-25 connector so can be replaced cheaply. Comes with a few extra cups, collets, and electrodes. The air regulator and lines and clamps work as they should. The power cord could be longer, but that’s an easy fix. The cutting torch isn’t bad, and the protector on it is nice. Over all, fantastic for the price. Hasn’t died yet. Nice and portable, worked out of the box and setup is very easy.

This was first time I've ever used a plasma cutter. I choose this machine because it was the most reasonably priced of all the machines I viewed. It came the day that it was projected to be delivered. The assembly was very simple if you have any mechanical skills. Although, the instructions are short on details. It would be helpful if the machine came with chart on how much air pressure and cutting amps for various metal thicknesses. I'm still not sure what one of knobs does or what to set it at. The machine worked fine and I was able to accomplish all of my projects without any problems.

This is my first plasma cutter so I am not an expert but so far this has made life alot easier as I am restoring an old rusted car. It makes short work of getting old parts out of the way. My only complaint is the extra consumable electrodes that it came with were slightly different than the one that was already in the head of the unit when I got it and when I went to replace the electrode it no longer would strike and cut. I had or another set of consumable that were the shorter length like what came in the head of the unit to begin with. It is very hard to get it to strike and start cutting on rusted metals but this may be a normal thing for all plasma cutters, I dont know. I am an amateur but I would still buy it again. 6 Month update...Wanted to come back and tell people that this thing is still going strong...it cuts through 1/4 steel like its not even there. I can not imagine working without it. As far as the complaints I had before I learned that you need to take a wire brush to the place you will be starting your strike from and it cuts like a dream. The rust acts like and insulator keeping it from getting started. Once started it flies through it...this is only severe rust I am talking about...like 60 year old car floor boards sitting in a field type of rust. 3 year update....one of the best tools I have ever purchased. I have learned alot with it. Watch your air pressure, it does not need to be high. Also this torch is designed for direct contact to strike....no need to wire brush the rust. Still love it. Over 4 years now and it is a wonderful tool to have around. Works great.

Purchased this item to use in my home shop. Arrived in good order without damage. Seemed like solid construction. I got the 110/220 version and started with the 110 side of things. It blew the breaker on 110 so I had a 220 installed with correct plug socket ($80 that I won't get back with this purchase). Tried it again and it was better and worked well for 15 minutes. I must have cut about 9 inches of plate and the unit just stopped functioning. The unit turns on and the fan runs. There is a "O/C" light (Overcharge, Open Circuit, Orange County...) that came on as a result of when I try to engage the machine. I changed the tip, unplugged it, reset the breaker, redid all of the connections, and inspected the unit for damage. Nothing I could see was wrong. I checked the "owner's manual" (all seven pages of poorly worded phrases) which didn't even list the "O/C" light. The fault checklist mentions damage to a board, and as though I am to inspect it. Even though, they clearly state that I should not "dismantle" it. So the obvious con is that the unit failed after about 30 minutes of use (max). Other cons: Owner's manual is of no value. Doesn't even mention how much PSI you should have running through the machine from the air hose. The air fittings and tighteners are poor and leak. Received this email from the seller. I changed the text below only to delete my name and the link to my review. Not sure what Amazon's policy on monetizing feedback, but I would consider it unethical. It also seems to be written by the same individual who wrote the instruction manual. Letter of apology to my dear Amazon customer friend dear ***** ****** Thank you for your recent purchase Customer comments are very important to us and we value your response. Please let us know how to help you solve your problems. We apologize for the inconvenience and thank you for the opportunity to correct the problem. Can you delete bad comments? c'mon. We will give you Amazon Gift Card as compensation You can reply to your request by SMS. Customer service team thank you Product review link: ******** As an apology, we want to make up for you. If it is convenient, you can contact us at any time, and we will provide the best help. By doing so, we hope you can update your comments on us. Many thanks for your help

I seen this little plasma cutter and decided to go ahead and buy it. It's been an excellent purchase. I've used it a few times. It works excellent. You're not going to be there for the money.

Good little plasma cutter. bought for small home projects on a car build. Cuts great for it size. Good for someone who wants a compact unit and not take up a bunch of space.

I have been using the cutter on 240volt and have not tried it on 120volt. It it working great. It took about 15 minutes to complete the setup and start using. I would recommend.

tutto

問題なく使えました

He recibido el aparato, cuando lo he podido conectar ni siquiera se pone en marcha la chispa para cortar. El contacto de salida estaba sin conectar. He tenido que abrirlo y conectarlo con un tornillo.

Das Gerät ist super es geht wunderbar es wäre schön wenn man bei dem Luft an Schlüssen Dichtungen oder Etwas anders mit rein legt weil so ist es nicht dicht 👍

Conditionnement parfait, produit à la hauteur de mes attentes et une expedition super rapide... Que demander de plus ?